胶模的英文

• jelly mo(u)ld

• "胶"英文翻译    glue; gum
• "模"英文翻译    mould; pattern; matrix
• "（凝）胶模" 英文翻译 :    gel mold
• "水胶模" 英文翻译 :    hydrocolloidal impression
• "塑胶模" 英文翻译 :    plastic rubber mould
• "橡胶模" 英文翻译 :    rubber model; rubber pattern
• "防水橡胶模" 英文翻译 :    liquid-tight rubber mold
• "黑胶模式" 英文翻译 :    vinyl mode
• "胶模印花纸" 英文翻译 :    slide-off transfer
• "凝胶模压法" 英文翻译 :    green stock molding
• "梳[电泳胶模" 英文翻译 :    comb
• "塑胶模具" 英文翻译 :    mould of plastics
• "塑胶模粘剂" 英文翻译 :    plastic coating adhesive
• "塑胶模座" 英文翻译 :    mold base
• "塑性凝胶模" 英文翻译 :    plastigel mo(u)ld; plastigelmould
• "橡胶模成形" 英文翻译 :    rubber pressing
• "橡胶模冲压" 英文翻译 :    rubber compression
• "橡胶模具" 英文翻译 :    rubber molding
• "橡胶模膨胀" 英文翻译 :    matrix swell
• "橡胶模型架" 英文翻译 :    rubber model frame
• "橡胶模压床" 英文翻译 :    hydroform press
• "橡胶模子" 英文翻译 :    o moulds for rubbers
• "压胶挤胶模" 英文翻译 :    rubber pressurized and extruded die
• "注塑胶模具" 英文翻译 :    plastic injection moulding
• "格林式橡胶模" 英文翻译 :    guerin press

• The pastern mold adopts wearable and heat - resistant silica gel , the aluminium mold can come to 200
  胶模采用耐磨热硅胶;外铝模温度可达200
• For label cutting blade of 12mm thickness and under . equipped with 26 male and female notches suitable for bending and cutting
  本机适用于加工12毫米以下的不干胶模切刀，配备26个阴阳模，具有弯刀和切刀两用功能。
• Pull the slip board , up distance switch to loosen , the film motor starts turn to move after receive the signal , turning to schedule length , pass the sense switch control film electrical engineering automatically stop , put the cup into the bottom slip mold , then push to go into , next circulation beginning
  拉出下模滑板，上行程开关松开，胶模电机接到信号后开始转动，转过预定长度，通过电眼控制胶膜电机自动停止，将胶杯放入下模滑板，再推入，下一个循环开始。
• The repair effect was compared with various type of repair parameters such as patch thickness young ' s modulus and thickness young ' s modulus of adhesive layer . in the chapter iv , a thermalstatic mechanical loading analysis of the repair problem was made . for the single side repair , the patch material having the maximum mismatch in the coefficient of thermal expansion with that of the crack aluminum plate provides the better damage tolerance capability for single - side crack in the panel
  模拟计算表明：粘胶模量增大， j积分值降低，修补效果与粘胶模量有关；随着粘胶厚度的增大，修补模型的j积分值略有增大后再逐步减小，应合理选择粘胶的厚度，尽量避免选择j积分较大值时的粘胶厚度；随着补片厚度的增加，修补模型的j积分值逐渐增大，到达一定量后又开始减小，因此补片的厚度需要合理选择。