shafting造句
- On one side, in the centre of the structure, are erected the lift shafts .
在结构中部的一侧设有电梯井。 - A gray brick tunnel, dimly lighted, led to the elevator shaft .
一条点着昏暗灯光的灰色砖砌通道通往电梯的并道。 - Find the required length of key based on the torque value of the gross shaft .
根据整根轴的扭矩值求需要的键长。 - Tom's heart gave a great thump, and he ran like the wind to the shaft .
汤姆的心怦的一跳,像一阵风似地奔到矿井。 - The fast-idle cam position is controlled by an arm on the choke shaft .
快怠速凸轮的位置是由阻风门轴上的杆臂控制的。 - Let the center of the global coordinates be chosen at the center of the shaft .
将总坐标的中心选于升降机井的中心处。 - Pawl is a simple device which allows a shaft to turn only one way .
掣爪是一种非常简单的只让转轴往一个方向转动的装置。 - An extension of the spindle shaft drives a counter for totalizing discharge .
心轴的延长部分带动一个累计流量的计量器。 - As the crankshaft rotates, the crankpin swings in a circle around the shaft .
随着曲轴的转动,曲柄销绕主轴作圆周摆动。 - The rotating slip ring is insulated from the shaft by a laminated plastic bushing .
旋转滑环是用片状塑料衬套与轴绝缘的。 - It's difficult to see shafting in a sentence. 用shafting造句挺难的
- A long time ago they laid the track into the valley, bored the mine shafts .
他们很久以前就把轨道辅进了山谷,打起了矿井。 - Usually in gyro designs the shaft member tends to run hotter than the outer member .
在陀螺的设计中,转轴构件通常比外部构件要热一些。 - The narrow shaft of the attack scope slid softly upward behind byron, and stopped .
拜伦背后进攻潜望镜的细镜筒悄悄地升起,最后停住了。 - The shaft of fig. 3-33 is simply supported at a and b and is keyed against rotation at a .
图3-33的轴被简支在A和B上,并在A处用键固定防止转动。 - The susceptor rested on a pedestal whose shaft is connected to a motor that provides rotation .
感应器安装在轴承台上,它的支架与提供旋转的马达相接。 - There is a hole in the shaft through which the air from the upper chamber enters the lower one .
腔筒中心有一孔道,压缩空气就是由此从上气室进入下气室的。 - Obvious examples are potentiometers and tachogenerators to monitor the position and speed of a shaft .
反映转轴位置和速度的电位器与测速发电机是我们最熟悉的例子。 - The more general case, when the shaft rotation may be significant, is dealt with in chapter 6 .
在较为一般的情况下,轴的旋转可能有显著影响,这种情况将在第六章中讨论。 - As the piston descended, a ratchet engaged the piston rod and engine shaft and thus power was transmitted .
当活塞下行时,棘轮连接活塞杆和发动机轴,因此将功率输送出去。 - Generally, two screws are placed in the hub: one screw bears on the key and the other bears on the shaft .
一般在轮毂内装有两个螺钉,一个螺钉压在键上,另一个则压在轴上。