faculae造句
例句与造句
- These faculae frequently are the forerunners of sunspot formation .
这些光斑常常是形成太阳黑子的先兆。 - Finally the influence of facula dithering on the guidance precision is estimated using the influence factor for some of aircraft weapons
通过引入影响因子来评价光斑抖动对制导精度的影响。 - Equip with facula control pipes , otherwise has alterable focus mirror facula . which can adjust 2mm to 6mm . provide choosing and buying for consumer
配有光斑控制管另备有变焦镜头光斑可在2 - 6mm调整，供用户选购 - Faculae ? extra - bright areas between granules ? appear to rise above the surface ; they may account for the increased output during solar maximums
米粒之间最明亮的光斑，则是在太阳极大期时，物质激烈喷发冲出表面所造成。 - It is comprised of a silicone rubber sheet , a wave - guide plate , an apparatus to apply three - axis force and facilities to capture faculae
它由一个硅橡胶垫、一个光波导路、一个三轴力加载装置和光斑的采集设备等组成。 - It's difficult to find faculae in a sentence. 用faculae造句挺难的
- This paper goes into details on the principle of faculae with maxwell electromagnetic theory . in conclusion : the planar wave - guide is just like a high pass filter
结果表明，当传感器受到外力f时，在波导中将有个模式不能继续存在于波导中而辐射出去。 - In the displacement measurement based on the principle of laser interference , the gaussian quadrics fitting algorithm is used to fix the central position of facula and raise the location accuracy
在基于两球面波干涉的长度和距离测量实验中,运用高斯二次曲面拟合算法为激光光斑的中心坐标定位,提高了光斑的定位精度。 - Through fea method , it ' s suggested that the areas of faculae have a specific relationship with the externally applied force on the sensor . the corresponding mathematical model is deduced from many simulations using the apdl program
在ansys中应用apdl语言编程，经过大量的模拟和仿真，建立了外力和光斑面积之间相应的数学模型关系。 - The faculae arise with change of the cutoff frequency when the wave - guide transforms from symmetry to asymmetry . for each pattern rank of the planar wave - guide , the light with the cutoff frequency change will be leaked out and captured by the ccd camera
对存在于对称平面波导中的各个模次的光，将有的光被泄漏，而ccd所摄到的则是其中被反射的一部分。 - Therefore , the component force in any direction can be easily calculated through the faculae captured by ccd camera , which provides a good solution to three - axis tactile sensing technology for intelligent robots
反之，可以很容易地通过光斑面积计算出圆柱触头所受到的外力，检测到在任意方向上的分力大小，从而为智能机器人三轴力触觉传感技术提供了一种新的解决方案。 - The contact areas between the four conical contact - tips and the wave - guide plate are not equal as three components of external force are unequal , and the corresponding faculae areas < wp = 8 > captured by ccd camera are different from each other
当三个方向分力大小不同时，就一个圆柱触头而言，下面的4个圆锥触头与丙烯板的接触面积不相等，因而位于丙烯板另一面的ccd摄像器所摄取到的光斑面积也不相同。 - When applying an external force on a columnar contact - tip , the corresponding four conical contact - tips will be pressed to the wave - guide plate , which breaks the condition of full inner reflection in the guided wave , and faculae arise because of the leaking light
圆柱触头受外力f作用时，对应的四个圆锥触头将受到挤压，由于光波导路中导波的全内反射条件遭到破坏而产生光泄漏，在波导板上形成光斑。 - It compute the parameter of deflexion caused by thermal distortion in orbit , deduce the general expression for spreading beam after thermal distortion of reflector and the center deflexion of facula received in ccd . with the method of fixing etc , it put forward the restrain measures adopted accordingly
计算了在轨运行条件下反射镜面热变形引起的表面法向偏转参数,推导了镜面变形后出射光线的通用表达式以及镜面变形前后在ccd探测器上的接收光斑中心偏转量的计算表达式。 - The result was identical with x - ray diffraction analysis . the photodamage resistance ability of in : linbo3 crystals was measured by the holographity mehod and the directly observing facula distortion method . it was shown that the photodamage resistance ability of in ( 2mol % ) : linbo3 crystals was two orders of magnitude higher than that of pure linbo _ ( 3 ) crystal
本文用全息法和直接观测光斑畸变法测试了in ： linbo _ 3晶体的抗光折变能力，结果表明， in ( 2mol ) ： linbo _ 3晶体的抗光损伤(光折变)能力比纯linbo _ 3晶体的抗光损伤能力提高2个数量级以上。 - The research is based on a type of low - cost desktop rapid prototyping system which replaces the laser with common uv light . in stereolithography process , once the cross - section contours is obtained through the slicing processing on stl model , it is needed to do more data processing such as inside and outside boundaries recognition , facula radius compensation , scanning and path planning to generate process control data
在光固化快速成型工艺中，当由切片软件对stl模型进行切片处理得到了层片截面轮廓后，为了形成加工控制数据，必须对截面轮廓进行诸如内外轮廓识别、工艺补偿、扫描及加工路径规划等一系列的工艺数据处理。
更多例句： 下一页
