But even if you make these changes and eliminate all the places where cmps are called outside of the scope of a global transaction , a load analysis tool one that measures the performance of the system under near production conditions , like 但是即使您做了这些更改，并且消除了所有在全局事务外部调用cmp的地方，负载分析工具（在生产环境下测量系统的性能） ，比如
The second part is load analysis . bases on the form - finding , the stress , strain and displacement etc are calculated under loads . also the problem of membrane drape and cable relaxation should be considered during this procedure 第二阶段是荷载分析阶段，即找形分析获得的曲面在各种可能荷载组合的作用下，求解其变形、位移、索膜内力及判别薄膜是否有褶皱产生或索是否有松弛现象。
Firstly , for the system of moulding board and support frame in construction the side pressure and screws are analyzed . the material and structure form of support frame are discussed . the design of support frame uses the method of limited state , and also it analyses the integer stability , part stability , and single stability , and then proposes the load analysis of multi - level support frame 首先，针对转换层梁模体系及支撑架施工，重点分析了转换层结构现浇混凝土对模板侧压力值及模板对拉螺杆的计算；讨论了转换层支撑体系的形式及构造，详细论述了基于极限状态设计的支撑架计算方法，包括纵横向水平杆的强度验算、立杆的整体稳定性、局部稳定性、单肢杆件稳定性等验算，并提出了多层支撑架的施工荷载计算方法。
The repair effect was compared with various type of repair parameters such as patch thickness young ' s modulus and thickness young ' s modulus of adhesive layer . in the chapter iv , a thermalstatic mechanical loading analysis of the repair problem was made . for the single side repair , the patch material having the maximum mismatch in the coefficient of thermal expansion with that of the crack aluminum plate provides the better damage tolerance capability for single - side crack in the panel 模拟计算表明：粘胶模量增大， j积分值降低，修补效果与粘胶模量有关；随着粘胶厚度的增大，修补模型的j积分值略有增大后再逐步减小，应合理选择粘胶的厚度，尽量避免选择j积分较大值时的粘胶厚度；随着补片厚度的增加，修补模型的j积分值逐渐增大，到达一定量后又开始减小，因此补片的厚度需要合理选择。
First , build the building model and air conditioning dynamic cooling load analysis model of the stock exchange in the basis of the experiment . second , calculate the air conditioning dynamic cooling load in summer ( april to october ) hourly by software simulation , obtain the maximum cooling load daily , the minimum cooling load daily , the proportion of each cooling load occupying the total cooling load and cooling load time frequence , analyse them by using twin load curves . last , contrast theoretical calculations with test results , analyse them and prove the model proper 首先，以实验为基础建立了证券营业部的建筑模型及空调动态冷负荷分析模型；其次，通过逐时逐日计算出了其夏季( 4月? 10月)空调动态冷负荷、各分项冷负荷在空调总冷负荷中所占的比例及空调冷负荷时间频数，并运用双负荷曲线法对每日最大冷负荷与每日最小冷负荷进行分析；最后，与实测数据进行对比，二者曲线基本符合，效果良好，证明所建模型适当。
In the condition of non - axisymmetrical stage separation in hypersonic flight , the problems of dynamics and kinematics of the validating vechicle and the launch vechicle are primarily analysised . it includes the movement of the center of mass and the rigid body of the vechicles , the relative movement of the different vechicles , the relative movement of the special parts of the different vechicles , the load analysis and the probable collision in the process of stage separation 研究了在高超声速状态下非对称级间分离过程中,验证飞行器与运载火箭分离时的相关运动学和动力学问题。包括:飞行体质心运动和刚体运动;不同飞行体之间的相对运动;不同飞行体上特殊部位之间的相对运动;分离过程中各相关飞行体上的载荷分析和分离过程中可能发生的碰撞问题。
