Avoid a pillow that is too thick . a pillow as thick as the width of one s shoulder is adequate 避免用太厚的枕头，使用一个肩膊高的枕头已足够。
That is why he allows these things to take place and unfold within our lives 这是神想我们听到的信息，我们却很难记住这信息，我们的头颅骨太厚了。
Only use light and non - bulky protective equipment , if it ' s too thick , you may gain a sense of false confidence 只使用轻而薄的护具，如果护具太厚，你可能会养成一种错误的自信。
At first , i didn ' t want to finsh the book because it was too long , but i hung in there and read it to the end 一开始的时候，这个书我不想读完，因为它太厚了，但是后来我还是一口气把它读完了。
The analysis of ultrasonic testing result indicated that main defects in the alloy were porosities likely caused by sintering thickness 对检测结果的分析和验证表明，其内部主要为孔隙类缺陷，产生原因可能是烧结厚度太厚所致。
The rib here is too thin and on the high side , so it will be difficult to fill here when we do the injection , can you increase the thickness of this rib 这个胶骨位胶太厚,而且高度偏高,注塑时很难填充这个筋位,可以增加这个筋骨位的厚度吗
It is not necessary to apply thick layer of ointment . a thin layer absorbs and acts more effectively . excess medication can irritate surrounding skin . apply only to necrotic areas 没有必要涂太厚的软膏。薄层软膏吸收更好，效果佳。过量药物可能刺激周围皮肤。只在坏死部位使用。
Especially on high - class sofa leather , the coating of the finishing process shall not be too thick , and it must cover up the natural defects shown at the surface and to evenly distribute the surface color , regulate the touch and glow of the leather surface , above all , it must have the best cohesion , bend - resist characters , also , it must have resistance for abrasive light , aging and color - migration , etc . 尤其高级沙发皮，涂饰的薄膜不可太厚，且要遮盖皮面一些天然的瑕疵和均匀表面的色泽，调整皮面的手感和光泽，更须要有很好的接著力、耐曲折性，又要有极佳耐刮摩性和耐光度，且能耐老化性、不吐色等之物性。
The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is , the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin , it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed , too high negatire - pressure may enlarge the flaw in casting 结果表明：保温涂料及一定的涂层厚度有利于提高铝液的充型速度；浇注温度越高、直浇道空心面积率越大，铝液充型速度越快；模样厚度太厚或太薄，均会使铝液充型速度降低；一定的直浇道长度及直浇道面积有利于提高铝液的充型速度；施加负压会使铝液的充型速度大大提高，但负压过大会增大铸造缺陷。
