Results show that the saw - tooth signal amplitude oscillate within small amplitude through the calibration 通过校准，锯齿波的幅值变化量可控制在很小范围内。
Abstract : this paper is mainly about an analog saw - tooth signal generator used for linear histogram test of adcs 摘要：主要内容是基于线性直方图法测量模?数转换器性能的片上模拟锯齿波发生器的实现方法。
Synchronized drive module produces horizontal drive signal in synchronization with horizontal synchronization signal and field drive sawtooth in synchronization with vertical synchronization signal . these signal drive scaning sytem of slltv 同步驱动模块产生与行、场同步的行同步驱动信号和场锯齿波驱动信号，用于驱动激光电视的扫描系统。
Make a comparison among different driving signals , including square , triangle , sinusoidal and sawtooth wave , it is shown that the square wave has the best driving result and the sawtooth wave has the worst one 实验还对方波、三角波、正旋波及锯齿波等几种不同的驱动信号产生微射流的效果进行了对比。结果表明方波信号产生的微射流最强，锯齿波产生的最弱。
After comparing three form ( rectangle , saw and sine wave ) of excitation force , the conclusion is drawed that the sine wave is much better than the other two waveforms . finally , multi - seedling virtual prototype is studied 另外，对比分析三种波形(矩形波、正弦波及锯齿波)激振力对振动系统的影响，发现采用正弦波激振力对振动系统冲击较小，应优先考虑使用。
Passive suspension , pid control semi - active suspension and neural network control semi - active suspension are researched by simulation . white noise , sine wave and sawtooth wave are used for excitation . the root mean square value of vehicle body acceleration , suspension displacement and vehicle wheel load are analyzed 在仿真研究中，路面激励取为白噪声、正弦波和锯齿波，悬架类型采用被动悬架、 pid控制半主动悬架、神经网络控制半主动悬架三种。
( 2 ) the properties of displacement measurement based on self - mixing interference are mathematically analyzed . first , how the external phase influences upon the output frequency , intensity , power and line - width is discussed . then , the output signal ' s properties modulated by four waves , including sine wave , square wave , triangular wave and saw tooth wave , is discussed ( 2 )通过数值分析讨论了自混合干涉位移测量系统的基本特性，包括外腔相位对输出光频、输出强度、输出功率、谱线宽度的影响，以及正弦波、方波、三角波、锯齿波调制反射体位移时输出信号的特点。
In the meantime , the all sub - circuits are also designed and emulated carefully including inverter , rs type flip - flop , voltage reference circuit , error amplifier , voltage comparator , sawtooth - wave generator , pwm comparator , soft activation circuit and so on . as a result , all of the sub - circuits answer the requirements . this chip has taped out with the 0 . 5um mix - signal process of csmc 本文利用cadenceeda集成电路设计工具、 spectres仿真工具,对集成电路内的各个模块包括反相器、基本rs触发器、基准电压电路、误差放大电路、电压比较电路、锯齿波振荡发生电路、 pwm比较电路、软启动电路、驱动电路等进行了具体的设计和仿真,且达到了预先设定的指标。
First , the system operation conditions that include three input types ( square , sinuous and triangle ) with different frequencies ( l / 250hz , l / 5hz and 1hz ) are discussed . in fault detection processes , we construct 4 three - layer bp neural networks to learn the normal states of the system . the outputs of trained neural networks are as the estimate values of the sensors 本文详细研究了在这种情况下的故障诊断问题，针对某液压系统，分析了系统在方波输入、正弦输入、锯齿波输入下，分别在正常工作频率、极限工作频率以及接近极限工作频率等9种工作状态的特性，以及在这9种工作状态下，运用神经网络观测器进行传感器故障诊断研究。
