flange造句

• These include gusset plates welded to the flange .
  这些包括焊接到翼缘上的节点板。
• An electrified wire can be strung along the outer edges of this flange .
  在外缘引上一条通了电的电线。
• The web and flanges of the main girders were fabricated from astm a441 steel .
  主梁的腹板和翼缘用ASTMA441钢制造。
• The engine-feed system interface is at the turbopump inlet flanges .
  发动机与供应系统的交界是在涡轮泵的进口法兰盘处。
• Three structures have exhibited cracking at the ends of flange gusset plates .
  已有三个结构在翼缘节点板端部出现了裂纹。
• Both flange and web exhibited satisfactory elongation characteristics (i.e. 28%) .
  翼缘和腹板都有令人满意的延伸率（即28）。
• Small rectangular backup bars were used to fabricate the web-bottom flange connection .
  在腹板与下翼缘的施焊中使用小矩形挡板。
• During fabrication slots for the stringers flanges were flame cut into box girders .
  制造时，为安装纵梁翼缘，在箱型梁中用焰割法开槽口。
• Every lens has a mounting flange with which it is attached to the camera body .
  每个透镜都有一个安装凸缘，依靠它才能把透镜安装到相机上。
• Cracks have been found in the flange and web splices at groove welds in at least four bridges .
  至少在四座桥梁的翼缘板和腹板拼接坡口焊缝中发现了裂纹。
• The initial retrofit consisted of removing the gaps between the stringer flange and floor beam by providing shims .
  最初的修复工作是通过垫片来消除纵梁翼缘和横梁之间的间隙。
• The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection .
  第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
• The crack surfaces in the web and flange were subjected to visual examination in order to evaluate crack growth regions .
  为了估计各裂纹扩展区，对翼缘和腹板的裂纹表面进行了宏观检验。
• The behavior and performance of the cracked flange plates suggest that good levels of fracture toughness exist in the a 517 steel .
  开裂的翼缘板的性能及使用状态说明A517钢的断裂韧性良好。
• These cracks occurred at either the beam flange or in the column flange depending on the reentrant corner weld angle .
  这些裂纹视凹形焊角的不同，或者出现在横梁翼缘上，或者出现在立柱翼缘上。
• At the top flange there would be enough slack so that no relative twist of any significant magnitude would be introduced into the girder web .
  在上翼缘处有足够的松动，因而在主梁腹板上并不会引起很大的相对扭转。
• A reliable machine shop can cut away a small amout of metal from the aft side of the mounting flange so that the lens will set closer to the film platen .
  可以请经验丰富的机械加工车间从安装凸缘的后部切削掉少量的金属，这样就能使透镜更加靠近胶片平面。
• Visual observations showed that a horizontal displacement in the longitudinal direction of the bridge developed between the tie girder and the top flange of the floor beam at the end connection .
  肉眼观察表明：在端节点处的系梁和横梁上翼缘之间产生一种沿桥梁纵向的水平位移。
• Of course , the unit can be mounted using flange hole
  当然，也可利用法兰孔安装。
• Jgd - e rubber seal valve base jgd - f rubber flange gland bush
  Jgd - e型橡胶密封阀座