industry control computer造句

• Design of industry control computer in tire sulphur turn process control
  在轮胎硫化过程控制中的设计应用
• The hardware uses a industry control computer based on pci bus and a signal converter
  硬件方面采用基于pci总线的工控机和一个信号调理器。
• It is mainly consist of large scale plc , industry control computer and other devices
  可以对热电厂中的主要热力系统的计算机控制系统进行仿真和调试。
• The hardware uses a industry control computer based on pci bus , a signal converter and daq ( date acquisition card to develop )
  硬件方面采用pci总线工控机、数据采集卡、信号调理器。
• In the test , the speed of revolution , temperature , oil supply pressure and other parameter are measured by the industry control computer
  采用工业控制计算机测试转速、温度、供油压力等参数。
• On the system platform of industry control computer , the interface and data processing unit are developed with senior language
  整个系统采用工控机作为测试系统的平台，使用高级程序语言开发测试系统的数据处理部分及测试界面。
• In addition , the main - station can communicate with two modes of sub - station within one version : industry control computer system and embedded system
  实际测试表明，系统的设计实现了预期的功能，并有效提高了通信的效率和可靠性。
• Resource collocation and mainly performance on inbuilt industry control computer - pc / 104 , which has been used in the hardware design , are introduced generally
  对其中所用嵌入式工业控制计算机? pc 104 ，在文中对其资源配置及主要性能特点做了全面的介绍。
• A distributing hardware control system of the stretch - bending machine is designed by combining the advanced industry control computer and plc ( programmable logic controller )
  采用先进的工业控制计算机与plc相结合的方式设计了分布式拉弯机硬件控制系统。
• Using embedded industry control computer , rebuild the controlling and steering part of fin stabilizer , substitute the former simulating parts and realize the digital in the control part . 3
  利用嵌入式工控机对减摇鳍的控制与操纵部分进行改造，代替原来的模拟器件，使控制部分实现数字化。
• This machine is controlled by the industry control computer , which can measure the clearance along the driving taper gear axes and select the suitable sleeves so that the clearance can be eliminated and the set tightening of the bearing can be achieved
  选垫机采用工业控制机控制、自动化检测驱动桥主锥齿轮轴轴向间隙，并优化选择合适的垫片，通过垫片来消除轴向间隙并调整轴承达到设定的预紧力矩。
• For the accomplishment of the national 863 - advanced project , the industry control computer is used as main control unite and the pwsm machine tools spindle drive system . the hardware and software of the system is studied and developed
  为完成该863课题，通过对以永磁同步电动机为执行元件的机床电主轴系统的数学模型的分析，提出了基于工业用控制计算机的永磁同步电动机全数字式机床电主轴系统的硬件和软件实现方案。
• The industry control computer is make up of lcd , hard disk , face pattern keyboard and net cards and modem etc , and can monitor waveform and data on the spot , and data can be passed to monitor center far away to be analyzed further by way of local area network and public telephone net
  工控机自带有液晶、硬盘、面模键盘、网卡、调制解调器等，可以在监测点就地显示监测波形和数据，而且可以通过局域网、公共电话网远传到监测中心进行进一步的分析研究。
• Adjusting digital potentiometer in controlling circuits of sps and capacitor charging and discharging circuit separately with industry control computer ( icc ) , the peak value and repeat frequency of output pulse can be adjusted separately . controlling relays to choose different capacitors with icc , the width of output pulse can be adjusted
  利用工控机分别调节开关式稳压电源控制电路和电容充放电控制电路中的数字电位器，就能分别调节输出陡脉冲的幅值和重复频率；利用工控机控制继电器选择不同的充放电电容，就能调节输出陡脉冲的脉宽。
• Firstly , the paper introduced the commonly hardware configure of microcomputer relaying and the function of every module of industry controlling computer std90386 . secondly , the paper introduced several types busbarprotection which was commonly installed on electric power system and the characteristic of mv or lv system with low current grounding . based on it , the paper put forwards the theory of percentage - restraint differential relay . after that , in the discussing every problems of the relaying working the paper put the emphasis on the negative effect of the ct saturation and countermeasure
  本文首先介绍了微机保护装置的一般硬件配置以及作为装置硬件平台的std90386工控机各组件模板的功能，然后分析了目前电网系统装设的母线保护的各种类型以及中、低压小电流接地电网的特点，在此基础上分析、介绍了作为本保护动作原理的“比率制动式差动保护”原理。
• On the basis of research on pumping station in changzhi iron and steel limited group company and analysis and research on the basic capability of industry control computer plc and state view software , this article adopt the systems analysis method to establish the frame of pumping station supervisory system based on " king view " , and propose the project to develop the distributed control system of pumping station ( ipc + plc ) using " king view " as supervisory software and siemens s7 - 200 as hypogynous machine
  在对长治钢铁公司泵站进行调研，对工业控制计算机可编程序控制器及组态王监控软件基本性能特点进行充分分析和研究的基础上，本文以系统分析的方法，构建了基于“组态王”的泵站监测系统框架，提出了以“组态王”为监控软件，可编程序控制器( plc )采用西门子s7 ? 200系列做为下位机的泵站分布式控制系统? ? ( ipc + plc系统)方案。