主轴转速的英文

• main shaft speed
• speed of main spindle
• spindle speeds

• "主轴"英文翻译    principal axis; chief axis; ...
• "转速"英文翻译    speed; revolution; rotation ...
• "主轴转速超控" 英文翻译 :    spindle speed over ride; spindle-speed over ride
• "主轴转速范围" 英文翻译 :    range of spindle speeds
• "主轴转速激活" 英文翻译 :    spindle speed active
• "主轴转速控制" 英文翻译 :    spindle speed control; spindle-speed control
• "主轴转速范围激活" 英文翻译 :    spindle range active
• "主轴转速级数和范围" 英文翻译 :    number and range of spindle speeds
• "轴转速" 英文翻译 :    shaft revolution; shaft speed; speed of spindle; speed; shock; speedofspindle; spindle speed; spindlespeed
• "主轴转盘" 英文翻译 :    spindle carrier
• "刀具轴转速" 英文翻译 :    cutter arbor speed
• "立轴转速" 英文翻译 :    rotational speed of spindle
• "曲轴转速" 英文翻译 :    crank shaft speed; crankshaft rotating speed; crankshaft speed; speed of crankshaft
• "凸轮轴转速" 英文翻译 :    camshaft speed
• "轴转速表" 英文翻译 :    shaft counter
• "轴转速范围" 英文翻译 :    spindle speed range
• "轴转速控制" 英文翻译 :    shaft speed control
• "艉轴转速表" 英文翻译 :    electric propeller shaft revolution indicator receiver
• "刀盘主轴转角" 英文翻译 :    cutter indle rotation angle; cutter spindle rotation angle
• "发动机轴转速" 英文翻译 :    engine shaft speed
• "螺桨轴转速计" 英文翻译 :    propeller shaft revolution indicator
• "轴转速传感器" 英文翻译 :    shaft speed transducer
• "轴转速指示器" 英文翻译 :    shaft revolution indicator; shaft speed indicator
• "检验工件主轴转角" 英文翻译 :    work tests roll
• "曲柄转角（主轴转角）" 英文翻译 :    crank rotation angle

• Spindle speed , and hence streaming performance , is critical
  主轴转速和流化性能是关键的。
• Main shaft speed
  主轴转速rpm
• ( 2 ) relation of quantity of fuel injection and needle vavle lift , rotation speed and pressure is got
  ( 2 )测定喷油量与针阀升程、喷油时间、主轴转速、喷油压力的关系。
• Obviously , the spindle rotations required to achieve these surface cutting speeds are directly related to the diameter of the tools being used
  显然，获得这表面切削速度所要求的主轴转速直接与使用的刀具直径有关。
• Mechanical problems of the spindle bearings , such as vibrations , run - out , and wear , have become one of these limiting factors
  硬盘主轴机械支承固有的问题如振动、跳动、磨损，就成为限制主轴转速提高的关键因素。
• Is between 150 to 900r min adjustable . the main axes adopts pneumatic clutching and braking fixture , while the workpiece
  主轴转速在150 900转min可调，主轴采用气动离合刹车装置，工件靠真空吸紧，一次装夹便可完成车削全过程。
• The whole programs are composed of main program , the oil injection count module program and the drive shaft rotation speed module program
  软件设计采用模块化设计方法，整个程序由主程序、喷油计数模块程序、主轴转速模块程序组成。
• The test stand after being rebuilded can autocontrol the oil injection count and the drive shaft rotation speed , which can be displayed digitally
  软件采用mcs - 51汇编语言进行编程。改造后的试验台可以自动控制喷油计数、主轴转速且数显。
• In this system , the variable frequency motor is applied to meet the requirement of low speed to check the compositive error and high speed to measure the vibration
  针对检测综合误差和振动时对主轴转速的要求，采用变频电机来控制主轴转速，以满足系统对转速的要求。
• To tackle this problem , a novel methodology is proposed to suppress the vibration of the spindle by means of chatter frequency identification and on - line regulation of spindle speed
  为此,本文采用辨识颤振频率和主轴转速在线调节的方法,与磁轴承控制相结合抑制主轴振动,取得良好效果。