地轴系的英文

• earth fixed axes
• ground axes

• "地轴"英文翻译    the earth's axis roller; spo ...
• "系"英文翻译    system; series
• "地轴系横轴" 英文翻译 :    lateral earth axis
• "地轴系立轴" 英文翻译 :    vertical earth axis
• "地轴系纵轴" 英文翻译 :    longitudinal earth axis
• "地轴系和轴系之间的方位角" 英文翻译 :    orientation angle s of earth to body axes
• "地轴" 英文翻译 :    axis of the earth; the earth's axis◇地轴 (承)架 floorstand
• "轴系" 英文翻译 :    axis series; line of shafting; line shafting; set of axes; shaft line; shaft system; system of axles
• "地轴架" 英文翻译 :    floor frame; floor hanger; floor stand; floor-frame; floor-stand
• "地轴弄" 英文翻译 :    screw alley; screw shaft alley; screw shaft tunnel; shaft passage; shaft trunk; tunnel
• "地轴室" 英文翻译 :    shaft room
• "地轴承架" 英文翻译 :    floor frame
• "地轴传动" 英文翻译 :    ground drive; ground transmission; grounddrive; groundtransmission
• "地轴弄，轴隧" 英文翻译 :    shaft tunnel
• "地轴倾斜度" 英文翻译 :    inclination of the earth's axis; inclinationoftheearth'saxis
• "地轴型盖板" 英文翻译 :    shaft tunnel ceiling
• "地轴转动" 英文翻译 :    nutation
• "南岭地轴" 英文翻译 :    nanling axis
• "秦岭地轴" 英文翻译 :    chin-ling axis
• "织机下地轴" 英文翻译 :    bottom shaft
• "侧轴系" 英文翻译 :    wing shafting
• "单轴系" 英文翻译 :    single shafting
• "吊轴系" 英文翻译 :    hanger shafting
• "多轴系" 英文翻译 :    multiple shafting
• "风轴系" 英文翻译 :    wind axes

• This paper presents the development and preliminary application works of an automatic strain gauge balance static calibration system in ecs for 1m hypersonic wind tunnel of cardc
  本文论述了cardc超高速空气动力研究所1m高超声速风洞配套的新型全自动六分量应变天平地轴系( ecs )校准系统的研制和初步应用研究工作。
• The position measuring system was another important system in the new balance calibration system . to work out the calibration loads in the bcs of balance with the results of balance position measuring is the key technique to improve the veracity of the balance calibration results
  通过天平空间位移测量并将地轴系校准载荷换算到天平体轴测量坐标系后再进行天平校准系数计算,是保证本文所研制的地轴系天平校准系统静校结果准确性的关键技术途径。
• According to the study work of this paper , an automatic six - component strain gauge balance calibration system development scheme was put forwards : the system calibrates the balances in the ecs , and translates the loads to the bcs of the balances with measuring the balance ’ s position changes during the calibration
  本文根据1m高超声速风洞气动力试验的总体要求,提出了采用天平校准载荷地轴系全自动加载、并通过天平空间位移测量将校准载荷换算到天平体轴系( bcs )的六分量天平校准系统总体研制方案,并确定了详细的技术指标。