预焙的英文

• prebake
  ◇预焙电解槽 prebaked cell; 预焙炭板 prebake carbon slab; 预焙阳极 prebaked anode

• "预"英文翻译    in advance; beforehand
• "焙"英文翻译    bake; torrefy; heat over a s ...
• "预焙烧" 英文翻译 :    preliminary roasting; preliminaryroasting; preparatory roasting; preroasting
• "预焙电解槽" 英文翻译 :    prebaked cell
• "预焙烧炉" 英文翻译 :    preroastfurnace
• "预焙炭板" 英文翻译 :    prebaked carbon slab
• "预焙阳极" 英文翻译 :    prebaked anode
• "连续预焙阳极" 英文翻译 :    continuous prebaked anode cell
• "预焙烧 预先焙烧" 英文翻译 :    preroast
• "不连续预焙阳极" 英文翻译 :    discontinuous prebaked anode
• "多预焙阳极电解槽" 英文翻译 :    cell with prebaked multiple anodes
• "预焙阳极电解槽" 英文翻译 :    prebaked-anode type cell
• "预焙阳极铝电解槽" 英文翻译 :    prebaked cell for aluminum-reduction
• "敞开式预焙阳极电解槽" 英文翻译 :    open prebaked anode type cell
• "预备姿势" 英文翻译 :    close stance; closed stance; commencing position; crouch position; get set; guard posing; on guard position; poise; position at bar; ready position; set position; stance
• "预备状态" 英文翻译 :    mode standby; readiness; ready condition; ready state
• "预备逐步增大产量和发布产品" 英文翻译 :    prepare for ramp-uand launch of the product
• "预备指示灯" 英文翻译 :    ready light
• "预备指挥所" 英文翻译 :    alternate command post

• Anode carbon for aluminium electrolysis
  铝电解用预焙阳极
• Guide for sampling plan and core sampling of prebaked anodes used in aluminum production
  铝生产中预焙阳极的取样方案和芯取样指南
• Technique code for retrofitting soderberg cell into prebaked anode cell in aluminium smelters
  自焙阳极铝电解槽预焙化改造技术规范
• Effects of preheating and start - up procedure on pot - life of prebaked anode aluminum reduction cell
  焙烧启动方法对预焙铝电解槽槽寿命的影响
• Carbonaceous materials used in the production of aluminium - sampling methods - part 3 : prebaked blocks
  铝用炭素材料取样方法.第3部分:预焙阳极
• Standard guide for sampling plan and core sampling for prebaked anodes used in aluminum production
  铝生产用预焙阳极的取样计划和芯取样的标准指南
• Failure of pre - baking al electrolytic cells under modern technical conditions causes and solutions
  现代工艺条件下预焙铝电解槽破损原因及解决对策
• The size of baking the positive pole over a slow fire in advance allows the deviation to accord with the following regulations
  预焙阳极的尺寸允许偏差应符合以下规定： a长度，不大于0 . 1 %
• Aluminium electrlysis by means of low molecular ratio electrolyte is an important mark for centre - worked prebake cell at present
  摘要采用低分子比电解质进行铝电解生产是现代中间下料预焙槽的重要标志。
• Aluminium cell test for energy balance and its calculation method - five - point feed current and six - point feed current prebaked anode aluminium cell
  铝电解槽能量平衡测试与计算方法五点进电和六点进电预焙阳极铝电解槽