pressure fuel造句

• Scavenge pressure fuel oil limit
  扫气压力燃油控制
• Diesel engines . technical requirements for high - pressure fuel injection pipe assmblies
  柴油机.高压油管组件.技术条件
• Diesel engines - high - pressure fuel injection pipe end - connections with 60 female cone
  柴油机. 60锥孔的高压油管接头管端部连接
• Diesel engines . high - pressure fuel injection pipe end - connections with 60 female cone
  柴油发动机. 60度锥孔的高压喷油管端部连接器
• Diesel engines . high - pressure fuel injection pipe end - connections with 60 degrees female cone
  柴油发动机.带60度锥形槽的高压注油管道端面连接件
• Diesel engines - high - pressure fuel injection pipe assemblies - general requirements and dimensions
  柴油发动机.高压燃料喷射泵组件.一般要求和尺寸
• Iso 2974 : 2000 diesel engines - high - pressure fuel injection pipe end - connections with 60 female cone iso 2974 : 2000
  柴油发动机. 60度高压喷油管端连接件
• Compression ignition engines - steel tubes for high pressure fuel injection pipes - requirements for composite tubes
  压燃式发动机.高压燃油喷管用钢管.合成管的要求
• Diesel engines - steel tubes for high - pressure fuel injection pipes - part 2 : requirements for composite tubes
  柴油发动机.高压燃料喷射管道用钢制管件.第2部分:复合管件的要求
• Compression - ignition engines - steel tubes for high - pressure fuel injection pipes . part 2 : requirements for composit tubes
  压燃式发动机.高压油管用钢管.第2部分：复合式钢管技术条件
• Longfeng thermoelectricity plant is medium temperature and medium pressure fuel thermoelectricity plant which built in 1960 ' s
  龙凤热电厂是六十年代建立起来的中温中压燃油热电厂。
• Compression ignition engines - steel tubes for high pressure fuel injection pipes - requirements for seamless cold drawn single wall tubes
  压缩点火发动机.高压注射燃油管用钢管.无缝冷拔单壁管要求
• Compression - ignition engines . steel tubes for high - pressure fuel injection pipes . part 1 : requirements for seamless cold - drawn single - wall tubes
  内燃机.高压注油管用钢管.第1部分:无缝冷拔单壁钢管的要求
• Diesel engines - steel tubes for high - pressure fuel injection pipes - part 1 : requirements for seamless cold - drawn single - wall tubes
  柴油发动机.高压燃料喷射管道用钢制管件.第1部分:无缝冷拉单壁管件的要求
• Compression - ignition engines - steel tubes for high - pressure fuel injection pipes . part 1 : requirements for seamless cold - drawn single - wall tubes
  压燃式发动机.高压油管用钢管.第1部分：单壁冷拉无缝钢管技术条件
• Compression - ignition engines - steel tubes for high - pressure fuel injection pipes - part 1 : requirements for seamless cold - drawn single - wall tubes iso 8535 - 1 : 1990 amd 1 : 1993
  压缩点火发动机.高压燃油喷射管用钢管.第1部分:无缝
• Based on correctly describing high pressure fuel injection spray , a quasi - dimensional combustion model for forecasting performance and emission of high pressure common rail diesel engine is established
  在正确描述高压燃油喷雾的基础上，建立了一个能预测高压共轨柴油机性能和排放的准维燃烧模型。
• Although there have recently been some research of high - pressure fuel injection system , there is little literature published about high - pressure common rail type electronically controlled fuel injection system
  高压燃油喷射技术受到业内高度重视，国内也有些研究报道，可是对高压共轨电控喷射系统的研究却还很少。
• From 1990 to 1995 , the average annual inflation rate of residential rents was 3 . 1 percentage points higher than that of other items of household expenditure . rents grew from 20 . 6 percent of average household expenditure to 25 . 3 percent . such pressures fuelled demand for higher salaries , raising overall operating costs
  由1990年至1997年间，租金的增长较其他消费项目的增长高出三点一个百分点，同期间，租金占家庭消费开支的比例亦由百分之二十点六上升至百分之二十五点三。
• The experimental investigations were first conducted on diesel spray wall - impingement mixing process with or without a bump on a flat wall and in a combustion chamber by means of plif method in the self - made constant volume combustion spray simulation set - up which can reproduce the typical working conditions and high - pressure fuel injection of modern diesel engines . the simulation computation of a cfd code about them was then carried out
  首先在自行研制的、可以模拟现代柴油机典型工作环境及高压燃油喷射特性的定容燃烧喷雾模拟装置上用片状激光诱导荧光法（ plif ）对平壁上、燃烧室内不设置和设置bump的柴油喷雾撞壁混合过程进行了试验研究，然后又用cfd多维数值分析软件对其进行了模拟计算。