丝孔的英文

• threaded hole

• "丝"英文翻译    silk
• "孔"英文翻译    hole; opening; aperture
• "导丝孔" 英文翻译 :    thread eye
• "纺丝孔" 英文翻译 :    nozzle hole; nozzle opening; nozzle slit
• "菌丝孔" 英文翻译 :    hyphal hole
• "螺丝孔" 英文翻译 :    screw hole; tapped hole; tapping hole; threaded hole
• "吐丝孔" 英文翻译 :    orifice of spinneret
• "爱丽丝孔雀" 英文翻译 :    alice peacock
• "漏板喷丝孔" 英文翻译 :    bushing tip
• "螺丝孔钻" 英文翻译 :    tapping drill
• "螺丝孔钻头" 英文翻译 :    tap drill
• "喷丝孔板" 英文翻译 :    nozzle aperture
• "喷丝孔膨胀" 英文翻译 :    die swelling
• "喷丝孔膨胀率" 英文翻译 :    die-swell ratio
• "汽缸盖螺丝孔" 英文翻译 :    cylinder head bolt hole; cylinderheadbolthole
• "十字形喷丝孔" 英文翻译 :    cross-shaped spinneret orifice
• "喷丝孔膨胀效应" 英文翻译 :    die swell effect
• "喷丝孔膨胀性状" 英文翻译 :    die-swell behaviour
• "钥匙孔形喷丝孔" 英文翻译 :    key hole shaped orifice
• "多叶形纺丝孔的叶片尺寸" 英文翻译 :    arm size
• "开口销孔和金属丝孔" 英文翻译 :    fasteners split pin holes and wireholes; fasteners--split pin holes and wireholes
• "丝口接头" 英文翻译 :    screwed fitting
• "丝克伍事件" 英文翻译 :    silkwood
• "丝扣" 英文翻译 :    screw thread
• "丝康诺" 英文翻译 :    frances conroy
• "丝扣保护" 英文翻译 :    thread protector

• Hexagon socket head cap screws without hole for locking wire . iso thread 4 h class
  无紧锁丝孔内六角圆柱头螺钉. 4h类iso螺纹
• Hexagon socket head cap screws , fully threaded without hole for locking wire . iso thread 4 g class
  无紧锁丝孔全六角圆柱头全螺纹螺钉. 4g类iso螺纹
• Show s famously off - tune english is often a source of laughter on his show , so fans should be eager to hear the results
  大战的结果，阿修罗王往往打败，有一次他大败之后，上天下地，无处可逃，于是化身潜入藕的丝孔之中。
• After de - acetylating chitin , chitosan can be easily dissolved in a dilute acetic acid solution , and chitosan fibers can be made by extruding the solution into a dilute alkali solution
  甲壳素脱乙酰基后得到的甲壳胺可以很方便地溶解在稀醋酸水溶液中，经喷丝孔挤出后用稀碱中和沉淀即可得到甲壳胺纤维。
• The spinneret material used in melt spinning , the spinneret shape , the rheological behaviour of the melt in orifice , the spinneret microhole geometric important indexes , the orifice arrange mode , the orifice opened scope and distance , the spinneret thickness were introduced in detail
  摘要介绍了熔融纺丝所用喷丝板的材质、喷丝板形状、熔体在喷丝孔中的流变特征，喷丝板微孔几何形状重要参数，喷丝孔排列方式，开孔范围及孔间距，喷丝板的厚度。
• The simulation results show that the shaped degree is decreasing when the spinning temperature and intrinsic viscosity are increasing ; the spinning speed has little effect on the shaped degree when the pump mass throughput is constant ; the shaped degree is increasing with the increasing of pump mass throughput when the spinning speed is constant ; the cross air - blow conditions have much effect on the shaped degree ; the scope of shaped cegree is increasing when the aspect ratio of spinneret hole is increasing ; the shaped degree has obvious decreasing tendency in the small zone of spinning path and this decreasing became gently when the pump mass throughput is increasing
  模拟的结果表明：扁平纤维的异形度随着纺丝温度及特性黏度的升高而降低；泵供量一定时，纺速对异形度的影响不大；纺丝速度一定，异形度随着泵供量的增大而增大；吹风条件对异形度的影响较大；随着喷丝孔的长宽比的增大，异形度增加的幅度也较大；异形度在纺程上较小的区间内有明显的下降趋势，并随着泵供量的增加其下降的趋势变缓。