传质速率的英文

• ma tra fer rate
• mass transfer rate
• rate of mass transfer

• "传"英文翻译    commentaries on classics
• "质"英文翻译    nature; character; essence
• "速率"英文翻译    speed; rate; tempo
• "传质速度" 英文翻译 :    mass transfer velocity
• "传质" 英文翻译 :    ma tra fer; mass transfer
• "传质区" 英文翻译 :    mass transfer zone
• "递传质" 英文翻译 :    carrier
• "速率" 英文翻译 :    speed; rate; tempo 冷却速率 rate of cooling; 送纸速率 line feed; 速率测试 rate test; 速率计 [工业] speedometer; 速率控制 rate control; 速率控制器 rate controller; 速率调节器 speed regulator; 速率陀螺 rate gyroscope; rate gyro; 速率陀螺仪 rate gyroscope; 速率指示器 rate indicator; 速率作用 rate action
• "不稳定传质" 英文翻译 :    unsteady mass transfer
• "传质j因子" 英文翻译 :    j-d-factor
• "传质操作" 英文翻译 :    mass transfer operation
• "传质单元数" 英文翻译 :    number of transfer units; number of mass transfer unit; number of transfer unit
• "传质抚塔盘" 英文翻译 :    mass-transfer valve plate
• "传质过程" 英文翻译 :    mass transfer process; mass transport process
• "传质机理" 英文翻译 :    mass-transfer mechanism; mechanism of mass transfer
• "传质控制" 英文翻译 :    mass-transfer control
• "传质控制的" 英文翻译 :    mass transfer limited
• "传质设备" 英文翻译 :    mass transfer apparatus
• "传质系数" 英文翻译 :    coefficient of mass transfer; ma conductivity coefficient; ma tra fer coefficient; mass conductivity coefficient; mass transfer coefficient
• "传质因数" 英文翻译 :    mass-transfer factor
• "传质因子" 英文翻译 :    mass transfer factor
• "传质装置" 英文翻译 :    mass transfer rig
• "传质阻力" 英文翻译 :    mass transfer resistance; resistance of mass transfer; resistance to mass transfer
• "对流传质" 英文翻译 :    convective mass transfer; mass transfer by convection
• "化学传质" 英文翻译 :    chemical transmitter

• Mass transfer rate
  传质速率
• Effect of pore size distribution on mass transfer in direct contact membrane distillation
  膜孔径分布对直接接触式膜蒸馏传质速率的影响
• Compaction of microporous membrane and its influence on the mass flux of membrane distillation
  微孔膜的可压缩性及参数变化对膜蒸馏跨膜传质速率的影响
• The formation of 3 . 5 % nacl solution is almost similar to that of 3 . 5 % nacl thin electrolyte layer , just the mass transfer rate of the oxygen in the layer is more quicker than in the solution ? the test shows that the crack growth rate of wet - corrosion fatigue of lc4cs aluminum alloy in the layer is quicker than in the solution , and also shows that morphology of fatigue fracture in the layer is evidently distinguished from in the solution
  3 . 5 nacl溶液和3 . 5 nacl薄液层的化学组成几乎完全相同，只是薄液层中氧的传质速率较快。实验结果显示了在薄液层中， lc4cs铝合金的湿腐蚀疲劳裂纹扩展速率，大于在3 . 5 nacl溶液中的速率。实验还发现其疲劳断口的形貌，也与3 . 5 nacl溶液中的有明显区别。
• To solve the mathematic equations , the method based on condensation degree was used . the distributions of temperature , concentration and mass flux on the film surface ; of temperature and concentration in the vapor ; of heat transfer coefficient in the vapor and in the liquid were obtained by applying the model in the flow field
  采用冷凝度的方法对该数学模型进行求解，得出了汽相的浓度分布和温度分布，界面处浓度分布、温度分布和传质速率分布，以及汽相和液相的传热系数分布。
• Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type , centrifugal structure , higher spraying pressure , less aperture , initial water temperature and original state of the air , some conclusions are obtained , such as : the centrifugal nozzle with firing pin type , high pressure and little aperture has bigger air eddy and atomizing angle . the spaying liquid has high velocity . the droplet is small , and the heat and mass transfer velocity is high
  通过对撞针型结构、离心式结构、较高的喷水压力、较小的喷嘴孔径、喷水初温及待加湿空气初状态对雾化加湿效果的作用原理的重点分析，得到：撞针型高压小孔径离心式喷嘴具有较大的空气涡与雾化角，喷出的液体流速高、液滴小、水与空气传热传质速率高，撞针型结构提高了雾化加湿效率，高压小孔径的特点为雾化加湿提供了较大的能量，而喷水初温的升高会减小水的粘性力和表面张力，从而优化加湿效果。