体积量的英文

• volume flow rate

• "量"英文翻译    measure capacity
• "体积量, 总量" 英文翻译 :    volume dose
• "体积量度" 英文翻译 :    volume measure
• "体积量计" 英文翻译 :    volumetric flowmeter; volumetricflowmeter
• "体积量度单位" 英文翻译 :    cubic measure
• "一次压注容量, 一次压注模制的体积量" 英文翻译 :    volume molded per shot; volume moulded per shot
• "沉积量" 英文翻译 :    sediment yield
• "积量计" 英文翻译 :    integrating meter
• "积量图" 英文翻译 :    quantity diagram
• "累积量" 英文翻译 :    accumulation volume; cumulant; semi-invariant
• "容积量" 英文翻译 :    cubical content; volumetric capacity; volumetric quantity
• "虚积量" 英文翻译 :    stcked content
• "淤积量" 英文翻译 :    sediment deposition
• "体积" 英文翻译 :    volume; bulk; bulking; bigness; bodiness; size◇体积计 volumeter; volumometer; volumenometer; volumescope; 体积重量 bulkfactor
• "长期沉积量" 英文翻译 :    long-term sediment yield; long-time yield
• "沉积量以" 英文翻译 :    mg/cm ・ d
• "腐殖集积量" 英文翻译 :    humus reserve
• "积量计常数" 英文翻译 :    constant of integrating meter
• "积量频率计" 英文翻译 :    integrating frequency meter; master frequency meter
• "阶乘累积量" 英文翻译 :    factorial cumulant
• "金属沉积量" 英文翻译 :    amount of metal deposited
• "净沉积量" 英文翻译 :    net deposition; net sediment
• "累积量表" 英文翻译 :    cumulative scale; summation scale
• "累积量表法" 英文翻译 :    cumulative scaling
• "立木度, 蓄积量" 英文翻译 :    amount of growing stock

• We are used to gain the detection efficiency by making the standard samples , because of the different source of the environment samples , the component and density and volume of the samples ca n ' t entirely match those of the standard samples , so it is very difficult to make the standard samples , thereby , in order to conquered experiment difficulty , this article has calculated the detection efficiency of hpge - spectrometer by existing monte carlo code
  但由于待测环境样品的来源不同，其介质成份、密度和体积量可能相差很大，实验上又难以制作各种各样的标准样品，采用蒙特卡罗方法可以比较容易地解决这些问题，对此，我们采用蒙特卡罗方法，研究了高纯锗谱仪对不同环境样品的探测效率，解决了实验上制作各种标准样品的难题。
• In this thesis it was proposed to simulate the drawing , trimming , flanging by using error - adjustment method . the initial trimming lines would be adjusted and optimized in the computer by adjusting error . if the shape error between the flanging boundary line and the target is larger than prescribed , the redundant area is subtracted from the initial blank by some amount of volume along the deformation path , and the insufficient volumes are added to the initial blank by the same amount
  本文提出,利用基于变形路径的误差修正法( error - adjustment ) ,结合cae技术将对初始修边线的调试过程在计算机中进行模拟(包括拉延、修边、翻边、整形等)计算,通过控制翻边后零件成型边界与实际目标轮廓之间的尺寸误差来优化修边线,如果初始切边、翻边后的轮廓与目标体的边界存在较大偏差,则初始切边轮廓中多余部分单元将沿其变形路径以相同体积量被切除,不足部分则沿其变形路径以相同体积进行补偿。

• 体积量的法语：dose-volume