充气管的英文

发音:

"充气管"怎么读用"充气管"造句

英文翻译手机版

appendix
charging pipe
filling tube
gas filled tube
gas tube
gas valve
gas-filled tube
gas-filled valve
gaseous tube
inflation tube

"充气"英文翻译 aerate; aerify; air inflatio ...
"管"英文翻译 pipe; tube
"气管充气管" 英文翻译 : gas tube
"布制充气管" 英文翻译 : fabric inflating lead
"充气管路" 英文翻译 : charging line; loading line
"气球充气管" 英文翻译 : appendix
"充气管充液管" 英文翻译 : charging pipe
"充气管稳定器" 英文翻译 : gas filled stabilizer; gas-filled stabilizer
"充气管整流器" 英文翻译 : discharge-tube rectifier; gas-filled tube rectifier; gaseous conduction ectifier
"冷阳极充气管" 英文翻译 : tactron
"冷阴极充气管" 英文翻译 : tactron
"热阴极充气管" 英文翻译 : hot-cathode gas-filled tube
"充气管弛缓振荡器" 英文翻译 : gas-tube relaxation oscillator
"充气管的点火极" 英文翻译 : starter of gas tube
"充气管脉冲发生器" 英文翻译 : gas tube pulse generator; gas-tube pulse generator
"充气管噪声调制器" 英文翻译 : gaston
"充气支气管造影片" 英文翻译 : air bronchogram
"充气支气管造影术" 英文翻译 : air bronchography
"附录；附加物；充气管；阑尾" 英文翻译 : appendix
"孤光放电充气管" 英文翻译 : krytron
"弧光放电充气管" 英文翻译 : krytron
"压缩空气充气管路" 英文翻译 : compressed air charging line
"二氧化碳饱和罐充气管" 英文翻译 : stack of the carbonator
"热阴极充气管整流器" 英文翻译 : hot-cathode gas-filled rectifier
"充气" 英文翻译 : aerate; aerify; air inflation; gas charging; gas loading; gas up; gasing; inflation; topping-up; aerification; aeration; air charging

例句与用法

Gas tube surge - protective devices , test specifications for
充气管式电涌保护装置的试验规范
Measurement of the electrical properties of microwave tubes . part 7 : high frequency gas - filled tubes
微波管电性能的测量.第7部分:高频充气管
Harmonized system of quality assessment for electronic components - blank detail specification : photomultiplier tubes
电子元器件质量保证协调体系.空白详细规范.充气管
Measurements of the electrical properties of electronic tubes . part 17 : methods of measurement of gas filled tubes and valves
电子管电性能的测量.第17部分:充气管的测量方法
To inflate pull the tabs down firmly , but don ' t inflate while in the cabin . if your vest needs further inflation , blow into the tubes on either side of your vest
然后打开充气阀门，但在客舱内不要充气，充气不足时，请将救生衣上部的两个充气管拉出，用嘴向里充气。
To inflate ， pull the tabs down firmly , but don ' t inflate while in the cabin . if your vest needs further inflation , blow into the tubes on either side of your vest
然后打开充气阀门，但在客舱内不要充气，充气不足时，请将救生衣上部的两个充气管拉出，用嘴向里充气。
Being used the before - mentioned method , fold models of a column tube was established . by simulating analyses , effects of inflation velocity on the deployment process of different structures were investigated
本文还分别从理论和模拟两个角度对展开后,作为支撑结构的充气管进行了模态分析,考察了不同充气压力对充气支撑管的固有频率的影响规律。
Being used the before - mentioned method , models of short and long column tubes made of film were established , the deployment simulations of those were done , and the effects of folding to structure performance were studied . the methods of simulating for deployment process were studied
同时,针对较长充气管展开过程的控制性较差,从仿真模拟的角度提出了一种塑性搭接扣的约束方式,以提高充气管展开过程的可控性和稳定性,并模拟成功。
The model analysis of the deployed beams were studied in both theory way and simulation way . the differences of the beams in different pressures were studied . investigations showed that the method of modeling for short and long rolled beams is doable ; the process of fold maybe lead so large displacement and stress that membrane is damaged at local areas , ration and material wrinkle generates ,
研究结果表明:本文提出的分别针对短、长卷曲折叠充气管的建模方法是有效的;在充气管展开过程中,充气速度越大,展开的速度越快,但由于阻尼损耗,二者并非线性关系;充气速度过大不利于结构展开过程的稳定性;充气支撑管的气压越大其固有频率越高,但影响效果很小。
Firstly , the process of fold and deployment was divided into several steps . secondly , the relative geometry results of the last simulation step was picked up as the initial geometry configuration of current step , using the restarting technology provided by fem programs , then the models of a inflatable structure with an paraboloid shape were established
然后,基于ls - dyna970中的airbag模型,建立了卷曲折叠空间充气展开管的有限元模型,运用控制体积法将充气管离散为若干连续的腔,成功模拟了其充气展开过程,并研究了不同充气速率对充气管展开过程的影响规律。