冲孔的的英文

• punched

• "冲孔"英文翻译    punching; punched hole; pier ...
• "的"英文翻译    4次方是 The fourth power of 2 i ...
• "多孔的；冲孔的" 英文翻译 :    perforated
• "冲孔的穿孔的凿孔的" 英文翻译 :    punched
• "冲孔" 英文翻译 :    [机械工程] punching; punched hole; piercing; pierce
• "在一行程完成落料拉延和冲孔的模具" 英文翻译 :    compound combination die
• "孔的" 英文翻译 :    foraminal; foraminate
• "对板料作曲折送进以连续落料冲孔的压力机" 英文翻译 :    stagger cut press
• "打孔的，有孔的" 英文翻译 :    perforated
• "珠孔的,卵孔的" 英文翻译 :    micropylar
• "半冲孔" 英文翻译 :    spring slice
• "冲床，冲孔" 英文翻译 :    punch
• "冲孔；切料" 英文翻译 :    blanking
• "冲孔板" 英文翻译 :    punched-plate
• "冲孔带" 英文翻译 :    punched tape
• "冲孔机" 英文翻译 :    eyelet machine; hole puncher; perforating press; perforator; piercing press; plate punching machine; punch machine; puncturing machine
• "冲孔模" 英文翻译 :    forming die; perforating die; pierce die; piercing dies; piercingdie; punching die
• "冲孔器" 英文翻译 :    piercer; puncheon; puncher; punching pin; setting die
• "冲孔钳" 英文翻译 :    punched pliers; punching ni ers; punching nippers; punching pliers; punching tongs
• "冲孔筛" 英文翻译 :    punched-hole sieve; stamped sieve
• "冲孔台" 英文翻译 :    punch table
• "冲孔屑" 英文翻译 :    punchings
• "冲孔者" 英文翻译 :    puncher
• "缓冲孔" 英文翻译 :    cushion hole
• "钻探；冲孔" 英文翻译 :    boring

• Thermal fe analysis can predict punch and die temperature distribution during the cooling process . holes drilled in the die allow for faster cooling
  温度有限元分析可以预测冷却过程中冲床和模具温度的分布，模具中冲孔的冷却速度比较快。
• Because explosive shape is regular , steel plate mainly occurs shear damage similar to hole piercing , the extent of damage gradually increase with explosive mass increasing , finally explosion outcome will enter oilcan ' s interior from crevasse
  由于药柱形状规则，钢板主要发生类似冲孔的剪切破坏，破坏程度随炸药质量的增加而加强，爆轰产物会从钢板破口处进入油罐内部。
• After the introduction of the innovations and the improvements of foreign hydraulic shock absorbers , the profound cushion mechanics study is done aiming to the shock absorbers chosen for the thesis ; the cushion process of hydraulic shock absorbers can be divided into several stages , which include local pressure loss caused by across sectional area shrinking , sharp edge throttling and aperture throttling
  在对国外新型液压缓冲器的研究基础上，针对本课题所选液压缓冲器的结构特点，提出了分阶段建立机理数学模型方法。将液压缓冲器缓冲过程分为：由于流道断面突然收缩引起的局部压力损失阶段，缓冲柱塞的边缘和缓冲孔的边缘形成锐缘节流阶段，当缓冲柱塞进入缓冲孔中形成的缝隙节流阶段等三过程。