减速控制的英文

• moderator control

• "减速"英文翻译    moderate; reduce the speed; ...
• "控制"英文翻译    control; dominate; regulate; ...
• "减速控制阀" 英文翻译 :    dcv deceleration control valve; deceleration control valve
• "减速控制器" 英文翻译 :    retardation controller
• "减速控制系统" 英文翻译 :    dcs deceleration control system; deceleration control system
• "减速控制装置" 英文翻译 :    choke opener; deceleration control system
• "燃油减速控制" 英文翻译 :    fdc fuel deceleration control; fuel deceleration control
• "燃油减速控制阀" 英文翻译 :    fdv fuel decel valve
• "变速控制" 英文翻译 :    variable speed control
• "变速控制板" 英文翻译 :    change control board
• "变速控制阀" 英文翻译 :    transmission control valve
• "变速控制器" 英文翻译 :    variable speed controller
• "超速控制器" 英文翻译 :    overrun brake
• "超转速控制" 英文翻译 :    overspeed control
• "车速控制" 英文翻译 :    vsc vehicle speed control
• "怠速控制" 英文翻译 :    isc idle speed control; lac idle air control; （iac） idle air control
• "怠速控制阀" 英文翻译 :    iacv idle air control valve; idle air control valve
• "等空速控制" 英文翻译 :    constant airspeed control
• "等速控制" 英文翻译 :    constant speed control; constant velocity control; constant-speed control
• "等速控制器" 英文翻译 :    isodromic controller
• "调速控制器" 英文翻译 :    actiyator; actuator governor; speed regulation actuator; speed setting controller; speed setting cylinder
• "定速控制" 英文翻译 :    cc cruise control
• "多速控制器" 英文翻译 :    multispeed controller
• "高速控制器" 英文翻译 :    high eed controller; high-speed controller; hsc high speed controller
• "过失速控制" 英文翻译 :    post stall control

• Dcs deceleration control system
  减速控制系统
• Dcs deceleration control system
  减速控制系统
• Fdc fuel deceleration control
  燃油减速控制
• Dcv deceleration control valve
  减速控制阀
• Deceleration control system
  减速控制装置
• Fdv fuel decel valve
  燃油减速控制阀
• Since linear acceleration and deceleration make motor abruptly stop and start that create the sharp corners of the velocity profile , s - curve motion profile refers to solving the problems
  针对线性加减速控制策略会引起速度突变,造成冲击的问题,本课题还研究了s型加减速控制策略。
• As doing so , it can avoid creep when guaidways is in low speed . controller uses plc , it is used widely in industry . besides , the principle of step motor and its acceleration and deceleration control are described
  控制器采用了在工业控制中广泛采用的可编程控制器，另外还描述了步进电机的工作原理及其加减速控制。
• Most of the real - time tasks are controlled by pmac , such as scanning , interpolation , position control , acceleration and deceleration , input & output , writing the sampled points to the dpram and so on
  下位机完成扫描跟踪控制、插补运算、位置控制、加减速控制、面板和机床状态的输入输出处理等实时性任务。同时将工件表面坐标实时写入dpram 。
• The accelerating and decelerating of the step - motor during weaving and its driving principle were discussed , and the calculating method for parameters of the mechanical driving system was expounded with examples
  分析了步进电机在织造过程中的加减速控制方法以及步进电机的驱动原理，阐述了织轴驱动系统机械传动的参数计算方法，并以示例进行了说明。