前峰的英文

• leading peak
• leadingpeak
• prepeak

• "前"英文翻译    front
• "峰"英文翻译    peak; summit
• "前峰雪莲" 英文翻译 :    lc-sl153
• "前峰漂移速率" 英文翻译 :    pre-peak drift rate; pre-peakdriftrate
• "球状爆炸前峰" 英文翻译 :    spheric detonation front
• "前峰 前沿峰 谱带伸长 谱峰伸前" 英文翻译 :    leadingpeak
• "前封头" 英文翻译 :    front head; fronthead; fusing head
• "前分支阻滞" 英文翻译 :    anterior fascicular block
• "前分支" 英文翻译 :    anterior division
• "前锋" 英文翻译 :    1.(先头部队) vanguard 部队前锋昨晚已经出发。 the vanguard units started off last night.2.[体育] forward; playmaker; tackle
• "前分野" 英文翻译 :    anterior split field
• "前锋 朱芳雨" 英文翻译 :    zhu fangyu
• "前分生组织" 英文翻译 :    promeristem

• It has a sharp front with a snout that is about five feet high .
  它有一个陡前峰，前锋有一个高五英尺的鼻子。
• Leading edge cuts the front from the the main - voltage sinus after the zero - cross
  飞机螺旋桨的前边缘在零交叉只后阻断了高电压的前峰。
• To the north of front peak , there were a forest of peaks , and among these peaks were scattered lots of valley
  前峰以北，高岭百转，群峰林立，峰岭之间沟谷棋布。
• The tidal bore is the front of flood tide as the water lever rises suddenly , it is the result of nonlinear - formed tidal wave under some conditions
  涌潮是水位骤然上升的涨潮波前峰，是一定条件下潮波非线性畸变的结果。
• An equivalent flow length method was used to predict the filling pattern and transferred the tracing of melt front to computing weighted approximate shortest flow path on finite element mesh model
  该法将熔体前峰面的追踪问题转换为带权曲面上任意两点间近似最短路径的求解。
• A cold front moving down from canada and butting up against moisture out of the gulf of mexico has produced freezing rain , snow and flash floods from kansas down to texas and eastward into missouri
  一股冷空气前峰从加拿大南下，遭遇来自墨西哥湾的湿气，形成冰雨及大雪，并引起山洪暴发，受灾地区从堪萨斯州向南至德克萨斯州，向东进入密苏里州。
• First , according to the demand of vimp for resin system , the reaction kinetics and rheological of up resin are investigated and the optimal content of low additive profile ( lpa ) is determined . then vimp based on a high - permeable medium and grooves are studied by visual experiments , through which the appropriate high - permeable mediums are selected and the parameters of width , depth and spacing for flow grooves and spacing for supply grooves are optimized . furthermore , various factors affecting the mold filling process are discussed and the whole vacuum infusion procedures are described taking examples of the manufacture of a model boat and a sandwich panel in one infusion
  文中首先根据vimp对树脂体系的要求，对vimp用不饱和聚酯树脂体系的动力学和流变学性能进行了研究，确定了最佳低收缩添加剂的含量；对高渗透介质型和沟槽型vimp开展了实验研究，通过可视化实验优选出较好的高渗透介质，确定了引流槽的宽度、深度和槽间距及主槽的槽间距等工艺参数并进行了优化；对影响充模过程的各种因素进行了详细的讨论，并以模型船和夹芯面板的制作为实例描述了两种vimp的成型过程；在实验的基础上，建立了二维渗漏模型，采用控制体有限元法对高渗透介质型vimp进行了成型过程的计算机模拟计算，通过充模时间和流动前峰的计算值与实验结果的比较，验证本文所采用的数学模型和数值方法的正确性，其结果对实际生产具有一定的理论指导意义。