压实后的英文

• post-compaction

• "压实"英文翻译    compaction; ramming; densifi ...
• "后"英文翻译    behind; back; rear
• "压实" 英文翻译 :    compaction; ramming; densification
• "风压实" 英文翻译 :    wind packing
• "干压实" 英文翻译 :    dry compaction
• "过压实" 英文翻译 :    overcompaction
• "夯实；压实" 英文翻译 :    compaction
• "欠压实" 英文翻译 :    uncompaction; undercompaction
• "压实；夯实" 英文翻译 :    compaction
• "压实；硬化" 英文翻译 :    consolidation
• "压实板" 英文翻译 :    squeezeboard
• "压实材" 英文翻译 :    staypak
• "压实层" 英文翻译 :    compacted layer; compacted lift
• "压实的" 英文翻译 :    compacted; consolidated
• "压实度" 英文翻译 :    compactness; degree of compaction
• "压实段" 英文翻译 :    compacting segment
• "压实阀" 英文翻译 :    squeeze valve; squeezing valve
• "压实缸" 英文翻译 :    squeezing cylinder
• "压实功" 英文翻译 :    compactive effort
• "压实辊" 英文翻译 :    compaction roller; compressing roll; compression roll
• "压实机" 英文翻译 :    compacting press; compactor
• "压实力" 英文翻译 :    compaction effort
• "压实流" 英文翻译 :    compaction flow
• "压实率" 英文翻译 :    degree of compacting; specific compaction
• "压实面" 英文翻译 :    compaction plane

• General methods of test for pigments and extenders - determination of tamped volume and apparent density after tamping
  颜料和填充剂的一般试验方法.压实后压实体积和表观密度的测定
• General methods of test for pigments and extenders . part 11 : determination of tamped volume and apparent density after tamping
  颜料和填料的一般试验方法.第11部分:压实后压实容积和表观密度的测定
• Carbonaceous materials used in the production of aluminium - cold and tepid ramming pastes - preparation of unbaked test specimens and determination of apparent density after compaction
  铝生产用含碳材料.冷和微热捣实糊料.非烤试验样品的制备和压实后表观密度的测定
• To control the settlement of roadbed , the degree of compaction regulated by current criterion is not enough , the mechanics parameter of filler compacted - - deformation parameter should be considered and dual control criterion should be put in practice . to get upper deformation parameter of xigeda stratum filler , the percentage of mudstone should be controlled . the thickness of filling layer regulated by current criterion can be increased if the compaction car has proper function
  通过此次研究，获得了对路堤变形问题的新的认识，即为了控制路堤的沉降变形，不仅应满足现行规范中规定的压实度标准，还应该引入填料压实后的力学参数? ?变形模量值标准，实行双重控制标准，而对于昔格达地层这种混合填料，为了获得较大的模量值，应该控制填料中泥岩的含量；现行公路路基施工规范中对路堤填筑时分层填筑厚度的规定值，在压实机具功能满足的条件下，可以适当提高。