变位系数的英文

• displacement factor
• modification coefficient
• stand-off error

• "变位"英文翻译    deflection; deflexion; conju ...
• "系数"英文翻译    coefficient; ratio; modulus; ...
• "径向变位系数" 英文翻译 :    addendum modification coefficient; overlaarc
• "齿轮刀具变位系数" 英文翻译 :    cutter change factor
• "地球位系数" 英文翻译 :    potential coefficient of the earth; potentialcoefficientoftheearth
• "电位系数" 英文翻译 :    coefficient of potential; potential modulus
• "吨位系数" 英文翻译 :    tonnage coefficient
• "区位系数" 英文翻译 :    locational coefficient
• "声相位系数" 英文翻译 :    acoustic phase coefficient
• "四分位系数" 英文翻译 :    quartile coefficient
• "相位系数" 英文翻译 :    phase coefficient
• "置位系数" 英文翻译 :    setzfaktor setting factor
• "齿轮刀具变位系" 英文翻译 :    cutter change
• "薄膜电位系数" 英文翻译 :    membrane potential coefficient
• "共轭相位系数" 英文翻译 :    conjugate phase coefficient
• "相位系数畸变" 英文翻译 :    phase coefficient distortion
• "相位系数失真" 英文翻译 :    phase-coefficient distortion
• "等价二进数位系数" 英文翻译 :    equivalent binary digit factor
• "反应性空位系数" 英文翻译 :    void coefficient of reactivity
• "反应性水位系数" 英文翻译 :    liquid level coefficient of reactivity
• "变位" 英文翻译 :    [数学] deflection; deflexion; [语言学] conjugate; [地] shift◇变位齿轮 profile shifted gear; 变位断层 shift fault; 变位酶 [化学] mutase
• "下位系" 英文翻译 :    inferae
• "变位；挠度" 英文翻译 :    deflection
• "变位层" 英文翻译 :    disrupted horizon
• "变位带" 英文翻译 :    shift zone

• Cutter change factor
  齿轮刀具变位系数
• Geometrical design of cylindrical internal involute gear pairs ; diagrams for the determination of addendum modification coefficients
  渐开线啮合圆柱内齿轮副的几何设计:齿顶高变位系数测
• After thoroughly analyzing the influence of each pump parameters on the gear pump performance , the paper developes the criterion for optimum gear parameters , which can be utilizied in practice easily for gear manufacturing using normal involute gear hob with two - fillet type . the conclutions studied by the paper are : 1 . both the addendum coefficient and the deddendum coefficient of the pump gear should be 1 . 125
  以目前国内普遍使用的双圆弧头全齿高为2 . 5倍模数渐开线标准滚刀作为泵齿轮的加工刀具，通过对齿轮加工原理的分析，提出了欲使泵齿轮参数达到最佳，泵齿轮的齿顶高系数和齿根高系数都为1 . 125 ；对变位系数的确定应考虑到泵齿轮的根切、齿顶厚、重合度以及侧隙因素；泵齿轮为避免过渡曲线干涉，必然要存在根切现象。
• 3 . base on the numeric method of finite element , the influence of interrelated shift coefficient and tooth number z to bend intensity of gear is studied . with the increase of the tooth number , tooth root maximum pull stress decrease ; with the increase of the interrelated shift coefficient , tooth root maximum pull stress increase
  3 、基于有限元数值计算方法，分析了不同关联变位系数和齿数z对齿轮弯曲强度的影响：随着齿数的增大，齿轮最大拉应力减小；关联变位系数越大，齿轮最大拉应力越大。
• For cutting the composite lock gear with unequal tooth thickness , a study is made on the design method of gear sharper cutter with nonstandard parameter involute tooth profile and noninvolute tooth profile . the cutter tooth arrangement , the choice of teeth number of the cutter and the basic method of cutter design are discussed ; and a new method of choosing deflection factor by using limited area is presented . and the curve of relationship between rear angle on tooth crest and helical angle on tooth side of the cutter is given so as to give a basis for the gear sharper cutter to choose its parameters . to design nonstandard gear sharper cutter by adopting the method mentioned above will simplify the calculation and will increase the efficiency of design
  研究加工不等齿厚的非标准参数渐开线齿形，与非渐开线齿形复合的锁闭齿轮插齿刀刀齿的排列、刀具齿数的选择以及刀具设计的基本方法，介绍用限制区域选择插齿刀变位系数的新方法，并给出刀具齿顶后角与侧螺旋角的关系曲线，为插齿刀参数的选择提供依据.结果表明，采用上述方法设计非标准复合齿轮插齿刀，可简化计算和提高设计效率
• When there is no or lesser undercut , we can use the bend stress ' s algorithm of involute gear to calculate approximately the bend stress of gear with meshed medium belt , what we to do is to transit the interrelated shift coefficient to the according radial minus shift coefficient of involute gear , and the error can be controlled in 10 %
  在不产生或少量根切时，可用渐开线径向变位齿轮的弯曲应力计算方法来近似计算带式啮合介质齿轮的弯曲应力，只需将关联变位系数转化为相应的渐开线齿轮径向变位系数即可，其误差在10 %以内。

• 变位系数的日语：てんいけいすう へんいけいすう