后处理器的英文

• postprocessor

• "后"英文翻译    behind; back; rear
• "后处理" 英文翻译 :    after treatment; aftercure; afterflush; final treatment; finishing; later processing; post processing; post treatment; postproce ing; post-treating; post-treatment; postprocessor; processing, post; reprocessing; ug
• "采后处理" 英文翻译 :    postharvest handling
• "插秧后处理" 英文翻译 :    post transplanting treatment
• "成衣后处理" 英文翻译 :    garment finishing
• "镀后处理" 英文翻译 :    postplating
• "干法后处理" 英文翻译 :    non aqueous reprocessing; non-aqueous reprocessing
• "焊后处理" 英文翻译 :    after treatment; postweld treatment
• "后处理程序" 英文翻译 :    down stream; post processor; postprocessor
• "后处理方式" 英文翻译 :    post processing mode
• "后处理分析" 英文翻译 :    reprocessing analysis
• "后处理工厂" 英文翻译 :    reprocessing plant
• "后处理机" 英文翻译 :    post processor; postprocessor(postp)
• "后处理剂" 英文翻译 :    after-treating agent
• "后处理加工" 英文翻译 :    after-treatment process
• "后处理能力" 英文翻译 :    reprocessing rate
• "后处理设备" 英文翻译 :    post treatment equipment
• "后处理设施" 英文翻译 :    facility, post-processing; post-processing facility; reprocessing facility
• "后处理损失" 英文翻译 :    reprocessing loss
• "后处理行程" 英文翻译 :    reprocessing steps
• "后处理浴" 英文翻译 :    aftertreatment bath
• "后处理装置" 英文翻译 :    after treatment device
• "化学后处理" 英文翻译 :    chemical after-treatment; chemical reprocessing
• "甲醛后处理" 英文翻译 :    after treatment with formalin
• "浸出后处理" 英文翻译 :    post leaching operation

• An additional stage could be added to reduce the distortion further due to compression as a postprocessing operator
  可以附加一个步骤作为后处理器，以进一步减小压缩带来的失真。
• The development of net3dbrowser iges postprocessor is mainly discussed in the dissertation , including the following aspects : 1
  本文主要研究net3dbrowseriges后处理器的实现，包括以下几个方面： 1
• It includes pre - processor ( generating step - nc file ) , post - processor ( verifying step - nc file ) and use interface in ug
  它包括了前处理器(生成step - nc文件)和后处理器(验证step - nc文件)的设计及绘图软件ug下的用户界面设计。
• The fem software package sheet - forming is a punch - forming fem analysis software package running on the sgi / unix graphic workstation , mostly including the pre - processor module , the post - processor module and the solving module
  Sheet - forming是运行于sgi unix平台上的冲压成形有限元数值仿真软件包，其核心模块是前处理器、后处理器、求解器。
• And now we finish the step - nc file . in the process of designing post - processor , our aim is converting step - nc file to some type cnc control code , and in this way verifying the step - nc file gained from pre _ processor
  在后处理器的设计中，我们的主要目的是把step - nc文件转换成某种类型的数控机床控制系统的数据指令，以此来验证前处理器中得到的step - nc文件的正确性。
• ( 2 ) the process of nonlinear analysis is done repeatedly until the results are converged . after that , the results are translated to corresponding properties of those components in the post - processing module and compared with the actual engineering after the error is estimated
  ( 2 )经过反复多次求解，调整参数，在ansys后处理器中分析计算结果，得出各构件的各项力学性能指标，并估计误差。
• Netsdbrowser , a 3d graphics browser based on network , is composed of two function modules : iges postprocessor and rendering and interaction module supported by opengl , which constitute function plug - in modules of the 3d graphics browser embedded in the webex netmeeting
  基于网络的三维图形浏览系统( net3dbrowser )主要由iges后处理器和以opengl为支撑的绘制与交互操作两大功能模块组成，构成webex网络会议系统的三维图形浏览功能插件。
• This system is used like this : drawing the part in ug , and planning its process , and then getting step - nc file by the function redeveloped , at last converting step - nc file into control code of fanuc system . the result is satisfying
  本系统的使用过程是这样的：在ug绘图软件绘制出零件图，并进行工艺规划，利用二次开发的功能输出step - nc文件，然后使用后处理器的转换，得到fanuc系统的数控指令，验证step - nc文件的正确性，最后的结果是令人满意的。
• In this paper , with the help of the idea of software engineering , the object - oriented developing technique , structured software development method , the inter - process communications in windows and the fortran / c + + mixed programming technique , the windows version of the pre - processor and the post - processor module are developed : the pre - process module is parted as four function modules . the part of graphic display codes of the pre - processor and the post - processor module are translated and modified as background processes . the interactive graphic interface in windows style is designed as foreground processes
  基于软件工程思想，本文综合运用面向对象技术、结构化程序设计方法、 windows进程间通信技术、 fortran c + +混合联编技术，对sheet - forming的微机版本中的前、后处理器模块进行了研制：将前处理器模块进一步划分为四个功能模块；优化编译前、后处理器的图形显示部分代码并将其作为后台程序；设计windows风格的前台交互式图形界面；利用本文设计的中介程序实现后处理前台界面和后台程序之间的通信。