后排气的英文

• final vacuum

• "后排"英文翻译    back row
• "气"英文翻译    gas
• "后排" 英文翻译 :    back row 坐在后排的一个座位上 take a seat on a back row; 后排插上战术 back-setter-move forward play (球类运动)
• "传后排" 英文翻译 :    backrow set
• "后排右" 英文翻译 :    back raght; back right
• "后排中" 英文翻译 :    back centre; cb; centre back
• "后排左" 英文翻译 :    back left; lb
• "排气" 英文翻译 :    [机械工程] exhaust; aerofluxus; air-out; exit gas; ventilate; atmosphere; vent◇排气泵 exhaust pump; return pump; 排气导管 exhaust guide; 排气道 exhaust passage; steam exhausting way; vapour chimney; 排气风扇 scavenger fan; 排气风箱 exhaust blower; 排气罐 vent tank; 排气活门 exhaust valve, air escape valve; 排气活塞 exhaust piston; 排气机 exhaust machine; evacuating machine; gas exhauster; 排气孔 kicker port; deflation opening; vent; 排气量 displacement; air displacement; 排气扇 exhaust fan; 排气设备 exhaust equipment; 排气室 exhaust chamber; exhaust room; 排气烟道 draught flue; 排气装置 blowdown; exhaust; exhauster
• "后排保护" 英文翻译 :    back up
• "后排打法" 英文翻译 :    back play
• "后排队员" 英文翻译 :    back field player; back lihe player; back line players; back row player; back tk
• "后排肥管" 英文翻译 :    rear distributor spout
• "后排观众" 英文翻译 :    pittite
• "后排进攻" 英文翻译 :    back line offence/back row attack
• "后排扣球" 英文翻译 :    back attack
• "后排水杆" 英文翻译 :    aft water drain mast
• "后排位置" 英文翻译 :    back court position
• "后排席位" 英文翻译 :    back benches
• "后排中座" 英文翻译 :    middle rear seat
• "交配后排卵" 英文翻译 :    copulation ovulation; post-coital ovulation
• "前后排列" 英文翻译 :    tandem
• "前后排列的" 英文翻译 :    tandem
• "事故后排热" 英文翻译 :    post accident heat removal
• "宰后排酸" 英文翻译 :    post-mortem ageing
• "正厅后排" 英文翻译 :    parquet circle

• After sample is preheated , it should be kept in mould for 20 - 40s and then breathing , the pressure is added at last
  1 . 0注：模塑料预热后，可在模具中预压20 - 40秒后排气再加压。
• After moulding material is preheated , must join the mould 20 - 40 second then exhaust air in mould to add again to press
  1 . 0注：模塑料预热后，须在模具中合模20 - 40秒后排气再加压。
• Note : after moulding material is preheated , must join the mould 20 - 40 second then exhaust air in mould to add again to press
  1 . 0注：模塑料预热后，须在模具中合模20 - 40秒后排气再加压。
• Note the compression condition may be difference , because the shape , dimension , and usage of produce were difference , the condition adjustment must under the premise that did not reduce the product quality
  注：模塑料预热后，须在模具中合模20 - 40秒后排气再加压。
• Engine , the fuel consumption decreases by about 19 . 1 % . on the other hand , the fuel consumption of quasi - homogenous mixture lean combustion decreases by about 6 . 5 % compared with homogenous lean mixture combustion . three - ways catalyst ( twc ) + optimizing afr technology is used to remove nox emissions in oxygen containing exhaust gas
  本研究运用三效催化器+空燃比优化控制技术，利用三效催化器能一定程度降低nox排放的特点，控制发动机在优化空燃比下工作，将稀燃后排气中剩余不多的nox进一步催化。