喷射压力的英文

• expulsion pressure
• injection pre ure
• injection pressure
• jet pressure
• nozzle pressure

• "喷射"英文翻译    spout; spurt; jet
• "压力"英文翻译    pressure; tension
• "喷射压力表" 英文翻译 :    injection pressure gauge
• "喷射压力机" 英文翻译 :    ejecting press
• "酸喷射压力" 英文翻译 :    acid-injection pressure
• "空气喷射压力" 英文翻译 :    air injection pressure
• "喷射压力脉动" 英文翻译 :    injection-pressure fluctuation
• "喷嘴喷射压力" 英文翻译 :    nozzle injection pressure
• "燃料喷射压力" 英文翻译 :    fuel injection pressure; fueling injection pressure
• "燃油喷射压力" 英文翻译 :    fuel-injection pressure
• "氧化剂喷射压力" 英文翻译 :    oxidizer injection pressure
• "喷射压差" 英文翻译 :    injection differential pressure
• "喷射压降" 英文翻译 :    injection pressure drop
• "喷射压气机" 英文翻译 :    jet compressor
• "喷射压缩" 英文翻译 :    jet compression
• "反射压力" 英文翻译 :    reflected pressure
• "辐射压力" 英文翻译 :    radiation pre ure; radiation pressure
• "抛射压力" 英文翻译 :    throw pressure
• "声发射压力" 英文翻译 :    acoustic radiation pressure
• "声辐射压力" 英文翻译 :    acoustic radiation pressure
• "注射压力" 英文翻译 :    injection pressure
• "平均喷射压差" 英文翻译 :    average injection pressure differential
• "蒸汽喷射压缩" 英文翻译 :    steam-jet compression
• "辐射压力天平" 英文翻译 :    radiation pressure balance
• "聚焦辐射压力" 英文翻译 :    focused radiatn pressure

• Air injection pressure
  空气喷射压力
• Based on this model , the effects of geometric and structural parameters , such as injection pressure , rear pressure , length - diameter ratio , inlet round angle - radius ratio and non - axis symmetry of nozzle , on the distribution of the cavitation inside the nozzle are analyzed
  基于这一模型进一步分析了喷射压力、背压和喷孔长径比、喷孔入口圆角比、非轴对称喷孔等几何结构参数对喷孔内空穴分布的影响。
• The system has others virtues , such as wide fuel adaptability , little fluctuation of pressure , good seal performance , etc . the injector of direct injection is assembled from electronic controlled valve and diesel injector , and it is used in the experiment
  研究了多种燃料供应方式下的燃料供应系统，其中缸内喷射系统创造性地采用液压增压方式，其具备燃料适应性广、喷射压力可调( 2 12mpa ) 、压力波动小、密封性好等优点。
• A lot of photographs of atomization field on high pressure jet were obtained by the use of the energetic liquid injection device and laser holographic system , so that the properties of axial and radial droplets size distribution were revealed . the relations of droplet size distribution with injection pressures , nozzle and viscosity were discussed
  利用含能液体喷射雾化模拟装置及其全息摄影系统，得到了多种工况下液体药射流喷雾场的全息照片，揭示了喷雾场中液滴轴向和径向分布规律，分析了喷射压力、喷嘴形状、液体粘度等对射流破碎的影响。
• Based on the close analysis of the influence factors of the vertical bearing capacity , circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity , respectively . moreover , with analyzing the features of the calculation parameters such as materials of gunite mortar , jet pressure , diameter of the jet pipe , pile length , pile layout , a design theory for chemical churning pile composite foundation is proposed . then , the variation of the pipe deformation with loads , the deformation coordination of pile and soil are studied
  在此基础上深入探讨了旋喷桩的桩土受力特性及其复合地基的加固机理,从影响旋喷桩复合地基竖向承载力的因素入手,基于圆孔扩张理论给出了桩体竖向应力及旋喷桩复合地基的竖向承载力计算公式;通过对喷射浆液、喷射压力选取、喷射直径估算、桩长及桩位设计等各种计算参数的深入分析和研究,提出了一套相应的旋喷桩复合地基设计计算方法;通过计算分析,深入探讨了旋喷桩复合地基变形随荷载变化规律、桩和桩间土变形协调关系、桩土应力比及复合地基压缩模量的确定,并提出相应的设计方法和修正参数;此外,结合工程应用,对旋喷桩复合地基的施工技术及其现场质量检测方法进行了较全面的探讨。

• 喷射压力的日语：ふんしゃあつりょく しゃしゅつせいけいあつ