多孔玻璃载体的英文

• porous glass matrix

• "多孔"英文翻译    multiaperture; multihole; po ...
• "玻璃"英文翻译    glass
• "载体"英文翻译    carrier; supporter; isotopic ...
• "多孔玻璃" 英文翻译 :    cellulated glass; expanded glass; foamed glass; fritted glass; porous glass
• "多孔玻璃管" 英文翻译 :    porous glass tube
• "多孔玻璃模" 英文翻译 :    porous glass membrane
• "多孔玻璃膜" 英文翻译 :    porous glass membrane
• "多孔玻璃盘" 英文翻译 :    fritted glass disk
• "多孔玻璃滤板" 英文翻译 :    fritted glass filter plate
• "多孔玻璃滤器" 英文翻译 :    sintered glass filter
• "多孔玻璃陶瓷" 英文翻译 :    cellular glass ceramics
• "多孔玻璃圆板" 英文翻译 :    fritted glass disc
• "多孔玻璃圆盘" 英文翻译 :    porous glass disk
• "可控多孔玻璃" 英文翻译 :    controlled pore glass
• "【化学】烧结玻璃；多孔玻璃。" 英文翻译 :    sinter glass
• "多孔玻璃比表面" 英文翻译 :    specific surface of porous glass
• "多孔玻璃分离器" 英文翻译 :    fritted glass separator
• "多孔玻璃过滤器" 英文翻译 :    fritted glass filter
• "多孔玻璃孔径分布" 英文翻译 :    pore size distribution of porous glass
• "多孔玻璃离子膜" 英文翻译 :    porous glass ionic membrane
• "多孔玻璃滤菌器" 英文翻译 :    sintered glass filter
• "可控表面多孔玻璃" 英文翻译 :    controlled surface pore glass
• "玻璃载片" 英文翻译 :    glass slide
• "定孔玻璃珠" 英文翻译 :    controlled-pore glass
• "观察孔玻璃" 英文翻译 :    port glass

• In this paper the mechanism and operation process of preparing porous glass material by means of filling method are studied , then the macro - pore porous glass beads commonly used as carrier material are introduced and produced with an improved method of traditional filling method
  本文阐述了以填充法制备多孔材料的基本原理与过程，并通过对传统填充法的改进直接制备宏孔径、高强度的多孔玻璃载体颗粒。
• Beginning with the analysis of the effects , which are brought by the application of only one kind of pore - former and some other operating factors ( such as sintering temperature , warmth retaining time and so on ) , on the properties of the beads , e . g . , porosity , strength , size distribution of the beads and pores size , etc . , these effects are discussed in detail and the relationship between the factors is studied thoroughly . the use of mpf ( multi - pore - former ) is introduced for the first time , which is of the most importance and significance in this paper
  研究从造孔剂选用和烧结过程对颗粒的孔隙率、机械强度、孔径分布及粒度分布的影响入手，找出了造孔剂的种类及含量、烧结温度以及保温时间等因素对最终所得产品颗粒的性能影响及它们之间的相互关系，并首次提出将造孔剂复配使用来对填充法加以改进，无需扩孔处理，即能直接制备宏孔径、高强度、小粒度、比表面大的多孔玻璃载体颗粒。