对搭接的英文

• halved joint

• "对"英文翻译    answer; reply
• "搭接"英文翻译    lap; lap joint; lapped butt; ...
• "对搭接合" 英文翻译 :    half-lap joint; halved joint; halving
• "直齿对搭接" 英文翻译 :    short scarf; shortscarf
• "重接 相嵌结合 单裁口搭接 对搭接" 英文翻译 :    halvedjoint
• "搭接" 英文翻译 :    lap; lap joint; lapped butt; lapping; lapping joint; related joint; shiplap joint; single lap joint; strap-on; bonding
• "对搭结合" 英文翻译 :    halve
• "派对搭配" 英文翻译 :    pelmanism
• "搭接 搭接缝" 英文翻译 :    lappedjoint
• "搭接 端搭接" 英文翻译 :    lappedbutt
• "半搭接" 英文翻译 :    half-lap joint; lipped joint
• "边搭接" 英文翻译 :    edge lap
• "长搭接" 英文翻译 :    long overlap
• "搭接，叠接" 英文翻译 :    lajoint; lapjoint
• "搭接；叠榫" 英文翻译 :    lajoint; lapjoint
• "搭接板" 英文翻译 :    lap jointed sheeting; lap-joint sheeting; lap-jointed sheeting
• "搭接边" 英文翻译 :    overlap edge; overlapping edges
• "搭接层" 英文翻译 :    bonding layer
• "搭接带" 英文翻译 :    attachment strap
• "搭接的" 英文翻译 :    lapped
• "搭接点" 英文翻译 :    lapoint
• "搭接缝" 英文翻译 :    coped joint; lap over seam; lap seam; lap weld; lapped joint; lapped seam; overlap butt; seam lap; welted edge
• "搭接工" 英文翻译 :    lapwork
• "搭接焊" 英文翻译 :    end lap weld; lap seam welding; lw lawelding; overla ing welding; overlap welding; overlapping welding; overlawelding; lawelding; tie welding
• "搭接键" 英文翻译 :    pickup key

• The stability influence produced by serial communication is analyzed theoretically , which is about one point of the join - structure . the delay range arisen by serial communication in which the system is steady is figured out
  同时,从理论上分析了串行通信延迟对搭接结构单悬浮点系统稳定性的影响,得到了使系统稳定悬浮的延迟时间范围。
• When the join - structure is suspended , suspension state message between the two suspension points should be exchanged and the digital suspension controller will communicate with the sensor . this function is realized by rs - 485 serial communication
  在对搭接结构进行悬浮控制时,两个悬浮点之间需要实时交换状态信息,并且传感器与数字悬浮控制器之间也要传输数据,两类信息交换是通过rs - 485串行通信来实现的。
• Analysis of nonlinear finite - element for ultimate strength of 81 overlap tubular k - joints with ansys program is carried out in this dissertation . the influence of nondimensional joints parameters , , and ov on failure mode and ultimate strength of overlap tubular k - joints is studied . simultaneously , 27 tubular gap k - joints are analyzed for comparative purposes
  分析时考虑了四个无量纲参数，即支管直径与主管的直径之比；主管的直径与壁厚之比；支管壁厚与主管壁厚之比以及支管搭接率o _ v对搭接节点破坏模式和极限承载力的影响。
• By analyzing the influence of hemisphere pits with different dimension and ellipsoid pits with different aspect ratio on stress and strain distribution of lap joint , the possible propagation of fatigue crack was discussed , and the effects of localized pitting corrosion on the structural integrity of lap joints were discussed
  通过分析不同尺寸的半球形蚀坑和不同长短半轴比值的半椭球形蚀孔应力应变分布的影响，探讨搭接件疲劳裂纹的可能扩展方向，讨论局部孔蚀对搭接件结构完整性的影响。
• It is difficult to ensure the steady suspension of the join - structure if the control method of the two suspension points is designed independently , so the coupling force between the two points must be taken into account . in this dissertation , the model of the join - structure is built . the model is decoupled and linearized by differential geometry method
  但是,同一搭接结构上的两个悬浮点之间具有很强的耦合作用,在对搭接结构进行悬浮控制时,如果对两个悬浮点独立进行悬浮控制设计,很难使搭接结构稳定悬浮,因此必须考虑它们之间的耦合作用。

• 对搭接的日语：はめ継ぎ はめつぎ あいかき だんつぎ