导轴承的英文

• guide bearing
• pilot bearing
• steady bearing

• "导"英文翻译    lead; guide
• "轴承"英文翻译    bearing; axle bearing; beari ...
• "导轴承隔片" 英文翻译 :    pilot bearing spacer; pilotbearingspacer
• "导轴承托架" 英文翻译 :    guide bearing bracket
• "导轴承支架" 英文翻译 :    guide bearing bracket
• "导轴轴承" 英文翻译 :    guide bearing; guide spindle bearing; guide spindle beating
• "分瓣导轴承" 英文翻译 :    segment guide bearing
• "曲轴导轴承" 英文翻译 :    crankshaft pilot bearing
• "上导轴承" 英文翻译 :    u er guide bearing; upper guide bearing
• "上导轴承架" 英文翻译 :    upper bearing bracket
• "水导轴承" 英文翻译 :    turbine guide bearing
• "下导轴承" 英文翻译 :    lower guide bearing
• "响导轴承" 英文翻译 :    pilot bearing
• "向导轴承" 英文翻译 :    pilot bearing; pilotbearing; piston and rod assembly
• "主导轴承" 英文翻译 :    main guide bearing
• "离合器导轴承" 英文翻译 :    clutch pilot bearing
• "曲轴引导轴承" 英文翻译 :    crankshaft pilot bearing
• "上导轴承间隙" 英文翻译 :    upper guide bearing clearance
• "水导轴承间隙" 英文翻译 :    turbine guide bearing clearance
• "支枢式导轴承" 英文翻译 :    pivoted-pad guide bearing
• "支柱式导轴承" 英文翻译 :    pivoted pad thrust bearing; pivoted-pad guide bearing
• "离合器引导轴承" 英文翻译 :    clutch pilot bearing
• "导轴" 英文翻译 :    guide shaft; guide spindle; guiding axle; guiding shaft; leading axle; leadingaxle; steering axle
• "导轴衬" 英文翻译 :    guide bush; guiding bush
• "导轴瓦" 英文翻译 :    guide-block

• Research on water pilot bearings at pump station set
  泵站机组水导轴承的研究
• As lubricated with outside clean water , bearings are of long life
  导轴承由外接清洁水润滑，使用寿命长。
• Improvement of the large vertical pump unit diversion bearings installation method
  大型立式泵机组水导轴承安装方法的改进
• The slide bearing assembled in middle segment is separated from sewage by inside pipe
  中间节设有由内导管将污水隔离的滑动导轴承。
• The paper points out the main contents of the structure , involving the stator design , the rotor design , the thrust - bearing design , the guide - bearing design and the loaded - framework design
  本文给出了结构方案设计的主要内容,包括定子设计、转子设计、推力轴承设计、导轴承设计和负载机架设计5个模块。
• First , the system boundary of machines affecting the shafts , such as the guide bearings , seal , electrical and hydraulic forces , the water in the runner etc , is analyzed . and the mathematic model of the system boundary of the machine is built
  本文首先分析了对机组主轴系统影响较大的系统边界条件，如导轴承、水封、电磁拉力、转轮处的水体等，并分别建立了它们的数学模型。
• Second , adopting the linearity of oil film of the guide bearings , the transient response of the shafts is computed and analysis by integrating with willson method . because of the uncertain position of the shafts in the guide bearing , the model and solution method of nonlinear transient response of the shafts is discussed
  然后结合willson数值积分法，采用线性化油膜力，对机组轴系的线性瞬态响应进行了计算分析，根据机组轴系在瞬态响应中运动的不确定性，给出了由导轴承油膜力非线性所引起的主轴系统的非线性瞬态响应的建模及求解方法。

• 导轴承的日语：パイロットベアリング