尺寸允许偏差的英文

• permissible variation in dimension

• "尺寸"英文翻译    measurement; dimensions; siz ...
• "允许"英文翻译    permit; allow; enable; allow ...
• "偏差"英文翻译    deviation; offset; deflectio ...
• "带材的尺寸允许偏差" 英文翻译 :    wrought aluminium and aluminium alloy sheets and strips-tolerances on form and dimensions
• "允许偏差" 英文翻译 :    acceptable deviations; allowable deviation; allowable variation; deviation permit; permissible error; permissible variation
• "尺寸允许公差" 英文翻译 :    measurement allowance
• "预定允许偏差" 英文翻译 :    pre-established allowable deviation
• "最大允许偏差" 英文翻译 :    maximum allowable offset; maximumallowableoffset
• "尺寸允许公差范围" 英文翻译 :    measurement allowance
• "铝及铝合金管材外形尺寸及允许偏差" 英文翻译 :    wrought aluminium and aluminium alloy tubes--dimensions and deviations; wrought aluminium and aluminium alloy tubes-dimensions and deviations
• "供电电压允许偏差" 英文翻译 :    quality of electric energy supply admissible deviation of supply voltagee
• "化学成分允许偏差" 英文翻译 :    permissible variation of chemical composition
• "外形及允许偏差" 英文翻译 :    dimensions shape and tolerances for cold-rolled steel strips with a width lessthan 600mm
• "重量及允许偏差" 英文翻译 :    dimensionsshapesmasses and tolerances of seamless steel tubeses
• "允许尺寸偏差" 英文翻译 :    allowable dime ion variation; allowable dimension ariation; allowable dimension variation
• "成品化学成分允许偏差" 英文翻译 :    permissible tolerances for product analysis
• "电力系统频率允许偏差" 英文翻译 :    quality of electric energy supplypermissible deviation of frequency for power systemem
• "默许偏差" 英文翻译 :    acquiescence bias
• "容许偏差" 英文翻译 :    acceptable deviation; admissible deviation; allowable deviation; allowable variation; allowabledeviation; leeway; permissible deviation; permissible variation; tolerable deflection; tolerance deviation
• "允许偏心" 英文翻译 :    allowable offset
• "允许偏移量" 英文翻译 :    allowable offset
• "表面容许偏差" 英文翻译 :    surface tolerance
• "径向容许偏差" 英文翻译 :    radial tolerance
• "容许偏差区域" 英文翻译 :    region of admissible deviations
• "统计容许偏差" 英文翻译 :    statistical tolerance

• Wrought aluminium and aluminium alloy sheets and strips - tolerances on form and dimensions
  铝及铝合金板带材的尺寸允许偏差
• Permissible deviations in dimensions without tolerance indication for metallic sintered products
  无公差指示的金属烧结产品的尺寸允许偏差
• Rectangular bars of wrought nickel and nickel alloys , hot rolled ; dimensions , tolerances , static values
  热轧变形镍和镍合金矩形棒材.尺寸允许偏差静态值
• The size of baking the positive pole over a slow fire in advance allows the deviation to accord with the following regulations
  预焙阳极的尺寸允许偏差应符合以下规定： a长度，不大于0 . 1 %
• Pressed metal plates the size of deviation should be allowed to meet norms . pressure produced by the metal plates to allow the construction site with a standard deviation requirements
  压型金属板的尺寸允许偏差应符合规范的规定。压型金属板施工现场制作的允许偏差符合规范的规定。
• Note : we can produce the non - standard and agreed producets whose qualities are higher than the listed above and whose dirnension derariet are less than the gb standard according to the customers requirements
  注：本厂可以按用户要求生产高于表中所列各项技术指标的产品或小于国标外型尺寸允许偏差规定的非标协议产品。