差数的英文

音标：[ chāshù ] 发音:

"差数"怎么读"差数"的汉语解释用"差数"造句

英文翻译手机版

difference
◇差数序列 difference sequence

"差数法" 英文翻译 : mismatch method
"差数机" 英文翻译 : difference engine
"降差数" 英文翻译 : descending difference
"偏差数" 英文翻译 : deviation
"比分差数" 英文翻译 : margin
"残数法,差数法" 英文翻译 : method of residual
"差数标准差" 英文翻译 : standard deviation of difference
"差数概差" 英文翻译 : probable error of difference
"差数机差" 英文翻译 : probable error of difference
"差数计分" 英文翻译 : under average
"差数计分法" 英文翻译 : under average
"差数显著性" 英文翻译 : significance of difference
"差数序列" 英文翻译 : difference sequence
"等差数列" 英文翻译 : arithmetic progression (sequence); arithmetic progression(sequence); arithmetic sequence; arithmeticprogre ion（sequence）
"动力势差数" 英文翻译 : dynamical number
"价格差数" 英文翻译 : price gap
"密码子差数" 英文翻译 : codon differences
"偏差数值" 英文翻译 : amount of deflection
"平均数差数" 英文翻译 : difference between means
"色差数据线" 英文翻译 : psp-s180
"生活费差数" 英文翻译 : cost-of-living differential
"视差差数" 英文翻译 : differential parallax; parallax difference
"随机差数" 英文翻译 : random difference
"贴现率差数" 英文翻译 : discount difference
"差事，杂事" 英文翻译 : do errands
"差事" 英文翻译 : 差事[口语] not up to standard; poor

例句与用法

Airspeed indicators - table of differential pressure
空速指示器.压差数值表
Least - significant difference
最小显著差数
The pro - whaling screed was approved by a much thinner margin : 33 votes to 32
上一次关于捕鲸的冗长决议是以33票对32票的微弱差数通过的。
Is the budgeted $ 341 sufficient ? is the actual expenditure $ 311 adequate ? is the difference of $ 30 acceptable ? how do these compared with the reference points
预算的341足够吗？实际的311妥当吗？ $ 30的差数可接受吗？这些资料和参考点比较，情况如何？
Also ground is laid out for further study in fault diagnosis based on integrated neural networks . in study of the air defense missile system , since the range is variant , so we processed the remain signal and extracted comparable data features out of it
且针对导弹系统，由于射程的不同，对所获得的残差数据进行了相应的处理，使对残差数据处理所提取的特征量具有很好的可比性。
As both the meshing point and ball ' s center are on the given cylinder , a general method for developing the cam ' s profile is studied . it is proved that the profile of positive and negative transmission is unique if the face gear , the difference between face tooth number and ball number and the diameter of ball are the same . the concrete expression of meshing cam on given spatial cycloid profile , and the characteristics of the profiles are discussed
论文的主要工作包括： 1 、根据啮合点和钢球中心轨迹均在同一圆柱面上的特点，研究了给定端齿齿廓条件下求解凸轮齿廓的一般方法；论证了在给定端齿、齿差数和钢球直径相同的条件下，正负齿差啮合齿廓的唯一性；讨论了端齿为球面摆线时，凸轮齿廓的具体表达式，并研究了该齿廓的性质。