断面收缩率的英文

• contraction of area
• contraction of cross sectional area
• contraction percentage of area
• cross-sectional reduction
• necking
• percentage reduction in area
• percentage reduction of area
• percentagereductionofarea
• reduction of cro section
• reduction of cross sectional area
• reduction of cross-sectional area
• reduction of crosssection area

• "断面"英文翻译    section; fracture surface; p ...
• "收缩"英文翻译    contract; shrink
• "率"英文翻译    rate; ratio; proportion
• "断裂时断面收缩率" 英文翻译 :    reduction of area at fracture
• "缺口试样断面收缩率" 英文翻译 :    notch ductility
• "断面收缩" 英文翻译 :    area reduction; contraction of cross sectional area; cross-section contraction; cross-section reduction; necking; reduction of area
• "面收缩" 英文翻译 :    necking
• "收缩率" 英文翻译 :    contraction coefficient; contraction in percentage; contraction percentage; contraction ratio; degree of contraction; degree of shrinkage; o shrinkage; percentage of contraction; rate of contraction; rate of convergence; rate of shrinkage; shrinkage factor; shrinkage ratio; shrinking percentage; take up factor
• "收缩率，收缩化" 英文翻译 :    shrinkage ratio
• "表面收缩" 英文翻译 :    surface contraction; surface shrinkage
• "底面收缩缝" 英文翻译 :    bottom surface dummy joint
• "横截面收缩" 英文翻译 :    contraction of cro section; contraction of cross section
• "截面收缩" 英文翻译 :    contraction of size; reduction of area; size contraction
• "断面减缩率" 英文翻译 :    area reduction
• "断面缩率" 英文翻译 :    area contraction,percentage of; area reduction,percentage of; area reduction， percentage of; percentage of area contraction; reduction of area
• "断面压缩率" 英文翻译 :    reduction of cross sectional area
• "侧向收缩率" 英文翻译 :    lateral shrinkage
• "断口收缩率" 英文翻译 :    reduction of area at fracture
• "沸水收缩率" 英文翻译 :    boiling water shrinkage
• "干燥收缩率" 英文翻译 :    drying shrinkage
• "横向收缩率" 英文翻译 :    lateral shrinkage
• "计算收缩率" 英文翻译 :    die shrinkage
• "径向收缩率" 英文翻译 :    radial shrinkage ratio
• "卷曲收缩率" 英文翻译 :    crimp contraction
• "面积收缩率" 英文翻译 :    percentage reduction of area

• Reduction of cross section
  断面收缩率
• 434 we shall take the sample to test its physical properties ( mechanical properties , tensile strength , yield point , percentage elongation , reduction of area , impact value , brinell hardness )
  我们将取样试验其物理性能（机械性能、抗张强度、屈服点、延伸率、断面收缩率、冲击值、布氏硬度） 。
• 434 we shall take the sample to test its physical properties ( mechanical properties , tensile strength , yield point , percentage elongation , reduction of area , impact value , brinell hardness )
  我们将取样试验其物理性能（机械性能、抗张强度、屈服点、延伸率、断面收缩率、冲击值、布氏硬度） 。
• In the third ductility region , the reduction in area of the sn - undoped steel is larger than that of the sn - doped steel . this means that the hot ductility of the sn - undoped steel is better than that of the sn - doped steel
  在第类脆性温度区内，不含sn钢的断面收缩率大于含sn钢的断面收缩率，即不含sn钢的热塑性要比含sn钢的热塑性好。
• Evaluation of uncertainty of measurement in testing for materials at ambient temperature has been discussed , including tensile strength ; lower yield strength ; proof strength , non - proportional extension ; percentage elongation after fracture and percentage reduction of area
  摘要文章介绍了金属材料室温拉伸试验测量结果不确定度的方法，内容包括抗拉强度、下屈服强度、规定非比例延伸强度、断后伸长率和断面收缩率等性能指标。
• In order to research product properties of the cross wedge rolling ( cwr ) , a series of rolling experiments have been carried out on two - roller cwr under the condition of considering the variation of the original diameter , deformation temperature , area reduction and heat treatment methods and so on
  摘要为了研究楔横轧条件下工件的性能，在考虑原始棒料直径、变形温度、断面收缩率以及工件轧后热处理状态等的基础上，利用二辊楔横轧机进行了系列楔横轧轧制实验。
• Based on the hot tensile test results , there exists a cooling rate at which a minimum reduction in area occurs and the hot ductility of the sn - doped steel is worse than that of the sn - undoped steel . when the cooling rate is lower or higher than 10 / s , the hot ductility is increased
  连续冷却到750 800范围内拉伸时，存在一个冷却速率( 10 s ) ，以这个冷却速率进行冷却，试样的断面收缩率最小，热塑性最差；当冷却速率大于或者小于这个冷却速率时，试样的断面收缩率均会增大，热塑性增强。
• The mechanical parameters at high temperatures - reduction in area ( ra % ) and tensile strength ( o b ) are measured by means of gleeble - 2000 thermal simulating machine . fracture surfaces are analyzed by scanning electron microscopy and optical microscopy . the segregation of sn is also examined by auger electron spectroscopy
  通过测定试验钢种的高温力学参数(断面收缩率ra和抗拉强度_ b ) ，观察金相显微组织，分析扫描断口形貌，测试第二相析出物和俄歇能谱试验等方法，研究了残留元素sn及冷却速率对高温力学性能的影响。

• 断面收缩率的日语：だんめんしゅくしょうりつ しぼり だんめんしゅうしゅくりつ だんめんげんしょうひ だんめんりつ だんめんちぢみ