曲线控制的英文

• curues

• "曲线"英文翻译    curve; curved line
• "控制"英文翻译    control; dominate; regulate; ...
• "曲线控制点" 英文翻译 :    principal mark
• "规律曲线控制" 英文翻译 :    law controlled
• "炉顶曲线控制" 英文翻译 :    roof contour control
• "定义曲线控制点数量" 英文翻译 :    reparameterize
• "线控制" 英文翻译 :    line control, linked control
• "出线控制台" 英文翻译 :    outgoing line console
• "传输线控制" 英文翻译 :    transmission-line control
• "导线控制网" 英文翻译 :    traverse network
• "地址线控制" 英文翻译 :    address line control
• "第三线控制" 英文翻译 :    third wire control
• "多总线控制" 英文翻译 :    multibus control
• "干线控制器" 英文翻译 :    trunk controller
• "航线控制" 英文翻译 :    rudder control
• "红外线控制" 英文翻译 :    infrared control
• "基线控制" 英文翻译 :    baseline control
• "基线控制器" 英文翻译 :    base line positioning controller
• "极线控制" 英文翻译 :    pole control
• "集线控制器" 英文翻译 :    lcc line concentration controller
• "假线控制" 英文翻译 :    pad switching
• "接线控制" 英文翻译 :    line control
• "离线控制" 英文翻译 :    off line control; off-line control
• "料线控制" 英文翻译 :    stock level control
• "流水线控制" 英文翻译 :    pipeline control

• Curve model control parameter analysis of extended end plate connection
  关系曲线控制参数的研究
• When forestage dcs system or pid regulator happened fault , manipulator receiving failure signal immediately switch into manual control state , by keystroke controls operation signal output
  可分别带有一路pid控制输出及一路变送输出。具有多种曲线控制输出功能：可实现曲线控制暂停清零步进等。
• Firstly , a simplified model of the robot is established in solidworks , which is imported into the simulation software adams . and then the motion curves got from matlab are applied on joints control
  在solidworks中建立机器人的简化模型,导入仿真软件adams中,再利用matlab中得到的运动曲线控制虚拟样机模型的关节运动。
• In the process of degree reduction , two cases are considered respectively , one of which is about the case without conditions of endpoint interpolations , the other of which is about the case with conditions of endpoint interpolations of higher orders
  两种方法均考虑了不带端点插值条件和具有端点高阶插值条件的情形，并给出了降阶said - ball曲线控制顶点的显示表示式。
• This paper present an ideal and calculation method of the effective operating curve where cavitations characteristic is not change . based on the lifting - line and lifting - surface method , using effective operating curve to control the cavitation type and " new section " design method to extend the width of cavitation bucket . the width will almost increase 30 % than the common section
  提出了保持剖面空泡特征不变的有效运转曲线的思想和确定方法，在升力线和升力面的基础上，应用有效运转曲线控制空泡类型，采用“新剖面”设计方法扩大空泡斗宽度，其空泡斗宽度比常规剖面增加近30左右。