最大公差的英文

• maximum allowance

• "最大"英文翻译    maximum
• "公差"英文翻译    public errand; noncombatant ...
• "超过最大公差" 英文翻译 :    overmeasure
• "最大公倍数" 英文翻译 :    gcm
• "最大公测度" 英文翻译 :    greatest common measure
• "最大公因" 英文翻译 :    greatest common divisor
• "最大公因数" 英文翻译 :    greatest common divisor
• "最大公因子" 英文翻译 :    ggt; greatest common divisor; greatest common factor; groesster gemeinsamer teiler; higher common factor; highest common factor
• "最大公约" 英文翻译 :    highest common divisor
• "最大公约数" 英文翻译 :    gcd; greater common divisor; greater common factor; greatest common divisor; greatest common measure; highest common divisor; highest common factor; le plus grand commun diviseur; maximal common divisor
• "最大公称粒径" 英文翻译 :    nmas
• "最大公共子模" 英文翻译 :    greatest common submodule
• "最大公共子群" 英文翻译 :    greatest common subgroup
• "最大公称破碎比" 英文翻译 :    nominal maximum reduction ratio
• "最大公用子图形" 英文翻译 :    maximal common subgraph
• "大公" 英文翻译 :    grand duke◇大公国 grand duchy; 大公墓 necropolis
• "工人阶级最大公无私" 英文翻译 :    it is the working class that is most selfless
• "公差" 英文翻译 :    1.[数学] (等差级数中任意两项之差) common difference2.[机械工程] (允许误差) allowable error; allowance; tolerance; limit; remedy allowance 安装公差 location tolerance; 制造公差 manufacturing tolerance; 公差表 table of limits; 公差制 limit system
• "大公报" 英文翻译 :    impartial l'; l' impartial; la justicia; ta kung pao; ta-kung pao
• "大公岔" 英文翻译 :    dagongcha
• "大公岛" 英文翻译 :    dagong dao
• "大公的" 英文翻译 :    archducal; grandducal
• "大公国" 英文翻译 :    archduchy; grand duchy
• "大公鸡" 英文翻译 :    master cock
• "大公墓" 英文翻译 :    necropolis

• The analogue display occurs very fast and with a max . tolerance of 1 percent
  模拟显示屏反应速度很快，而且最大公差为1 % 。
• Material will be supplied un - straightened with straight cut ends on both ends . a commercial straightness tolerance of 5mm maximum deviation over 1 metre will apply
  供货时，不要求平直度。只在两端切直即可。平直度最大公差： 5毫米/米即可。
• Iso general purpose metric screw threads - tolerances - part 5 : limits of sizes for internal screw threads to mate with hot - dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
  Iso通用米制螺纹.公差.第5部分:与电镀前最大公差级为h的热浸电镀外螺纹配合的内螺纹尺寸的限值
• Iso general purpose metric screw threads - tolerances - part 5 : limits of sizes for internal screw threads to mate with hot - dip galvanized external screw threads with maximum size of tolerance position h before galvanizing
  Iso通用米制螺纹.公差.第5部分:镀锌前与最大公差尺寸位置h热镀锌外螺纹相配的内螺纹的尺寸限值
• 1 iso general purpose metric screw threads - tolerances - part 5 : limits of sizes for internal screw threads to mate with hot - dip galvanized external screw threads with maximum size of tolerance position h before galvanizing erratum 1
  Iso通用米制螺纹.公差.第5部分:与电镀前最大公差级为h的热浸电镀外螺纹相配合的内螺纹的尺寸极限值