梁翼缘的英文

• spar flange

• "梁"英文翻译    beam
• "翼"英文翻译    the wing of a bird
• "缘"英文翻译    reason
• "板梁翼缘接合" 英文翻译 :    plate-girder flange splice
• "钢梁翼缘宽度" 英文翻译 :    schenkellnge leg length
• "梁翼" 英文翻译 :    beam flange
• "翼缘" 英文翻译 :    flange girth; lip; wing edge
• "双梁翼" 英文翻译 :    wing; two spar
• "反翼缘" 英文翻译 :    counter flange
• "钢翼缘" 英文翻译 :    steel flange
• "上翼缘" 英文翻译 :    top flange; upper flange
• "下翼缘" 英文翻译 :    bottom flange; lower flange
• "翼缘板" 英文翻译 :    boom plate; chord plate; flange plate; flange slab; frange plate
• "翼缘钢" 英文翻译 :    flange steel
• "翼缘墙" 英文翻译 :    fin wall
• "板梁翼接合" 英文翻译 :    plate girder flange splice
• "梁翼盖板" 英文翻译 :    flange cover plate
• "梁翼歪斜" 英文翻译 :    beam flanges out of square; beamflangesoutofsquare
• "三梁翼盒" 英文翻译 :    three-spar box
• "受拉梁翼" 英文翻译 :    tension flange
• "双梁翼盒" 英文翻译 :    two-spar box
• "闭口式翼缘" 英文翻译 :    dead flange
• "底翼缘板" 英文翻译 :    bottom flange plate
• "蝶式翼缘" 英文翻译 :    flared out flanges
• "反翼缘法" 英文翻译 :    counterflange method

• During fabrication slots for the stringers flanges were flame cut into box girders .
  制造时，为安装纵梁翼缘，在箱型梁中用焰割法开槽口。
• The initial retrofit consisted of removing the gaps between the stringer flange and floor beam by providing shims .
  最初的修复工作是通过垫片来消除纵梁翼缘和横梁之间的间隙。
• The second crack is a crack originating at the groove weld toe of the column flange-girder flange connection .
  第二种是产生于立柱翼缘与主梁翼缘连接处的坡口焊缝焊趾处的裂纹。
• Analysis of flange effective distribution width of new type of gfrp composite beam
  组合梁翼缘有效分布宽度分析
• Studies have show that designing both the beam and the panel zone to participate effectively in dissipating the earthquake input energy is the appropriate failure mode
  研究结果表明，柱腹板与梁翼缘同时进入屈服来共同耗散地震能量是一种较理想的破坏模式，有利于节点延性的发挥。
• Second , change the diaphragm ’ s space between , retain the other thing , analyze the influence of the stress and deformation of box ? girder cross section and the beam web . based on the analysis upwards , the writer studied the rule of the influence of the stress and deformation box ? girder cross section and the beam web with different diaphragm ’ s space between . according to the results of finite element analysis , the writer puts forward some suggestions which will provide some reference for the following design
  本文利用ansys有限元分析程序,对指定断面,不同曲率的曲箱梁,建立完备的有限元模型,分别对二个方面的问题进行了分析:其一,通过对箱梁在有无跨中横隔板时截面顶板及腹板的变形和应力分布的对比分析,阐述了设置跨中横隔板的重要性;其二,在相同工况下,通过改变横隔板的设置间距,分析对箱梁翼缘及腹板的受力影响。