模内的英文

• intramode

• "模"英文翻译    mould; pattern; matrix
• "内"英文翻译    inner; inside; within
• "模内面" 英文翻译 :    inner die surface
• "锭模内脱氧" 英文翻译 :    deoxidation in ingot mould
• "模内动作" 英文翻译 :    internal mold action; internal mould action
• "模内发泡" 英文翻译 :    foam-in-place mold; foam-in-place mould; foaming in mould
• "模内飞边" 英文翻译 :    center flow
• "模内畸变" 英文翻译 :    intramodal distortion
• "模内接种" 英文翻译 :    direct mold inoculation
• "模内料淬冷" 英文翻译 :    in-die-strand quenching
• "模内流动性" 英文翻译 :    mold flow properties; mould flow properties
• "模内切割" 英文翻译 :    in-mold cutting; in-mould cutting
• "模内烫印" 英文翻译 :    in-mold hot stamping; in-mould hot stamping
• "模内贴标" 英文翻译 :    iml
• "模内涂布" 英文翻译 :    in-line coating
• "模内退火" 英文翻译 :    annealing in mold
• "模内修边" 英文翻译 :    in-mold trimming; in-mould trimming
• "模内压力" 英文翻译 :    in-mould pressure; internal mould pressure. cavity pressure
• "模内铸型" 英文翻译 :    in-line coining
• "模内装潢" 英文翻译 :    in-mold decorating; in-mold decoration; in-mould decorating; in-mould decoration
• "嵌入模内的" 英文翻译 :    molded in; moulded-in
• "胎模内腔" 英文翻译 :    matrix cavity
• "阴模内成型" 英文翻译 :    forming into female mold; forming into female mould
• "铸模内渣" 英文翻译 :    mold slag
• "超大规模内存" 英文翻译 :    vlm very large memory

• In - mould labeling manipulator
  一种高速模内贴标机械手
• Research into material - selecting for the lining of shaping die of funnelled brick
  漏斗砖成型模内衬选材研究
• Periodic kiln internal die pressure
  模内压力
• In - mould coating technique
  模内漆层技术
• Direct mold inoculation
  模内接种
• Annealing in mold
  模内退火
• Lightly pour half of the cheese filling into the prepared crust and place it in a freezer for 20 minutes until the surface has set
  把1 / 2的芝士馅料慢慢倒入饼模内，放入冰箱冻柜20分钟雪到表面凝固。
• Numerical simulation of three dimensiona isothermal power - law polymer melt flow within an extrusion die with the quot; l quot; shaped cross section
  型异型材挤出口模内聚合物熔体三维等温幂律流动的数值模拟
• Numerical simulation and analysis of polymer melt filling flow driven by a periodically oscillating entrance pressure through the extrusion die with an irregular cross - section
  振动场作用下聚合物熔体在异型材挤出口模内的充填流动分析
• The design guideline of the plastics products with insert film decoration and the position deviation experience tolerance of the film pre - form process are discussed
  同时讨论了模内复膜产品设计原则以及装饰膜的预成型工艺及其公差经验值。