注水量的英文

• water injection rate

• "注水"英文翻译    water injection; waterfloodi ...
• "量"英文翻译    measure capacity
• "减少注水量" 英文翻译 :    injection cutback
• "起始注水量" 英文翻译 :    head start
• "日注水量" 英文翻译 :    daily water-injection rate
• "增加注水量" 英文翻译 :    incremental water injection volume
• "自流注水量" 英文翻译 :    water dumping rate
• "平均日注水量" 英文翻译 :    daily average water injection
• "注水" 英文翻译 :    water injection; [石油工业] waterflooding 边缘注水 edgewater flooding; 注水泵站 water flooding pump station; 注水器 can filler; 注水试验 water injection test
• "水量" 英文翻译 :    water yield; the yield of water◇水量计[表] watermeter; 水量平衡 water balance; 水量收支 water budget
• "泵注水" 英文翻译 :    pump priming
• "试注水" 英文翻译 :    pilot flooding; pilotflood
• "水；注水" 英文翻译 :    water
• "再注水" 英文翻译 :    reinjection
• "注水泵" 英文翻译 :    water inject-pump; water injection pump; waterflood pump
• "注水点" 英文翻译 :    injection point
• "注水度" 英文翻译 :    injectivity
• "注水阀" 英文翻译 :    water injecting valve; water injection valve
• "注水法" 英文翻译 :    pump-in method; water flooding; water injection
• "注水盖" 英文翻译 :    filler cover
• "注水管" 英文翻译 :    flooding duct
• "注水后" 英文翻译 :    postwaterflood
• "注水壶" 英文翻译 :    topping ujug; topping up jug
• "注水井" 英文翻译 :    downflow well; inlet well; water injection well; water injector; water input well; waterflood input well; waterfloof injection well
• "注水孔" 英文翻译 :    flash hole; water injection hole

• Sensitivity analysis is made to injected water volume adjustment and reserves potential
  并对注水量的修正和储量潜力进行了敏感性分析。
• Experimental study on cycle process of an adsorption cooling tube under various water - charging conditions
  几种典型注水量下吸附式冷管的工作特性实验研究
• Electric water heater ; thermal storage water heater , wall mounting type , capacity 5 up to 150 litres rated input
  电热水器.第3部分:挂墙式额定注水量为5 - 150升的
• Electric water heater ; thermal storage water heater , floor mounting type , capacity 200 up to 1000 litres rated input
  电热水器.第3部分:立地式额定注水量为200 - 1000升
• With definite water injection timing and pattern , water injection intensity and , especially , the injection allocation rate is very important
  在注水电动机、注水方式一定的情况下，注水强度，尤其是各注水井的注水量配置显得非常重要。
• Because of inner - layer , interlayer and areal heterogeneity of reservoir , after a long period of water flooding , injected water circulates in high permeability channel , sweep volume cannot be enlarged , and injected water volume of per ton increases a lot
  摘要由于储层层内、层间及平面不均衡性，经过长期注水开发，导致注入水沿高渗透条带循环，很难进一步扩大波及体积，使得吨油注水量大幅度增加。
• In addition , in order to make the pumps realize constant injection pressure , the expert tuning pid vfvs constant injection pressure control sub - system for pumps is established and relevant software module is developed . the sub - system can control automatically the quantity and rotate speed of the pumps running to realize the pumps optimum run according to the seawater injection plan of the oil field , which realizes constant injection pressure , energy saving and decreases the consumption to a large degree
  此外，为平台注水泵机组的优化运行构建了基于专家整定pid控制的变频调速恒压注水控制子系统，并开发了相应的软件模块，完全省却了pid控制器的硬件设备，使得注水泵机组可以根据油田注水量的配注方案优化运行，自动控制注水泵的转速和运转台数，既能实现平稳增压注水，又能在很大程度上节能降耗。
• Based on the fundamental theory of dynamics of soil moisture and the condition of water storage pit irrigation , numerical modeling of soil moisture movement of single water storage pit in heterogeneous soil is established . adi ( alternating direction implicit method ) and gauess - seidel iterative method are used to solve it . by using the simulated value of modeling , the relation of water injection volume and maximum horizental distance of moisture frontal are concluded . according to the relation , interval of pits are derived . then , after analyzing the infiltration characteristic of soil moisture under the condition of interference infiltration in multi storage pit , numerical modeling of soil moisture movement of multi water storage pit in heterogeneous soil is established , and its numerical solution is also acquired
  利用adi (交替方向隐式差分法)结合gauess ? seidel迭代法对模型进行数值求解。利用模型的计算结果得出了单坑注水量与湿润锋最大水平推进距离之间的关系，并据此确定了坑距。在此基础上，通过对多坑干扰入渗条件下土壤水分入渗特性进行分析，太原理工大学硕士研究生学位论文建立了蓄水多坑非均质土壤水分运动数学模型，并对其进行数值求解。
• To some of injection wells which couldn ' t finished their proration water injection rates in low permeability reservoirs , through the technological innovation , jianghan oil region has conducted boosting pres sure for water injection on well groups , and has obtained good effects in oilfield increment oil production and stable oil production
  摘要江汉油区对低渗透油藏中完不成配注水量的部分注水井通过工艺技术革新，进行井组增压注水，在油田增产稳产中取得了良好效果。