泵出口的英文

• pumdischarge

• "泵"英文翻译    pump
• "出口"英文翻译    exit
• "泵出口压力" 英文翻译 :    pumdischarge pre ure; pump discharge pressure
• "泵排量；泵出口" 英文翻译 :    pumdischarge
• "泵出口控制阀" 英文翻译 :    pump discharge control valve
• "水泵出口扬程" 英文翻译 :    outlet head
• "推进剂泵出口" 英文翻译 :    propellant-pump outlet
• "液压泵出口阀" 英文翻译 :    oil pump outlet valve
• "给水泵出口压力" 英文翻译 :    feed pressure
• "燃料泵出口压力" 英文翻译 :    fuel pump output pressure
• "氧气泵出口短管" 英文翻译 :    oxygen-discharge flange
• "增压泵出口压力" 英文翻译 :    boost pump pressure
• "泵出" 英文翻译 :    pump-out
• "给水压力给水泵出口压力" 英文翻译 :    feed pressure
• "水泵出口阀法兰垫片" 英文翻译 :    water pumoutlet valve flange gasket
• "泵出点" 英文翻译 :    pumping point
• "泵出力" 英文翻译 :    pump delivery
• "泵出量" 英文翻译 :    pumoutput
• "泵出布置图" 英文翻译 :    pumping out arrangement
• "泵出系统" 英文翻译 :    pumping out system
• "舱室泵出" 英文翻译 :    bilge pumping
• "水泵出水管" 英文翻译 :    pumping line; water pump outlet pipe
• "水泵出水率" 英文翻译 :    pump capacity
• "油泵出油阀" 英文翻译 :    oil pump outlet valve
• "油泵出油管" 英文翻译 :    oil pump outlet line; oil pump outlet tube

• Mean the pump export diameter is 80 mm
  表示泵出口直径是
• Mean the pump export diameter is 32 mm
  表示泵出口直径是
• Mean the pump export diameter is
  表示泵出口直径是
• Ctc maximum head is suitable for pump discharge to butanol handling facility
  用户确认泵出口去丁醇处理装置的最大扬程是合适的
• Install 5 pipe diameters minimum downstream from pump discharge or elbows to avoid flow turbulence . flow straighteners may be required in extreme cases
  安装位置距泵出口或弯管下游处最少应该有5倍管道直径的长度的位置。极端情况下可能需要安装流向矫直装置。
• The centrifugal pump for oilfield waterflooding and oil transfer worked with low pump efficiency owing to unstable load and its energy loss is fairly large
  油田注水集输系统离心泵由于载荷经常变化，大多不能在其额定工况点工作，泵效低，且需要用泵出口阀调节流量，产生一定的泵管压差，造成较大的能量损失。
• Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process , the reasons for the unsteady running were studied , the modification measures such as lubricating the oil groove with sliding bearing , mechanical sealing of the gear pump , decreasing the gear pump outlet pressure , changing the automatic speed increasing to hand speed increasing were put forward
  摘要通过对聚酯装置增容和后接直纺长丝前后熔体齿轮泵工况变化的统计分析，研究其运行不稳定的原因，提出改造措施，包括滑动轴承润滑油槽，齿轮泵的机械密封，降低齿轮泵出口压力，改自动提速为手动提速等等。
• This system tests 19 parameters such as the pressure of fore and after main fluid pumps and every sub fluid pumps " , force of pedal , turn angle of steering wheel , speed of every wheels and car body , and calculates 9 correlation analyses according to the gb112676 - 1999 " automobile system structure , capability and test methods " and gb7258 - 1997 " technical regulation of automobile safety " , also it can generate data report automatically
  该系统对汽车制动过程中前后液压总泵出口液压、各制动分泵进口液压、脚踏板力、方向盘转角、各车轮转速、车体速度等共计19个物理量进行测试。系统硬件由便携式计算机、数据采集器以及相应传感器组成。硬件设计中采用了模块化设计思想，使得测试系统体积小、重量轻、抗振动、安装拆卸方便、易于维护、可以进行随车实测试验。
• Thirdly , geometry modeling of the pump was made and meshes were divided with gimbit , then the flow filed was investigated using flunt , a commercial available cfd code . as result , lots of internal flow filed of outlet of the gear pump was obtained , including velocity magnitude and pressure magnitude
  应用pro / e和gambit软件对机油泵进行几何建模并划分网格,应用fluent软件模拟多种工况下机油泵出口部分的三维湍流流动,得到详尽的三维湍流场的分析结果,包括压力分布图、速度矢量分布图等。