流动模拟的英文

• flow simulation

• "流动"英文翻译    ent] population; floating pe ...
• "模拟"英文翻译    imitate; copy
• "流体流动模拟" 英文翻译 :    fluid flow analogy; fluid-flow analogy
• "进气道流动模拟" 英文翻译 :    intake flow simulation
• "流动模" 英文翻译 :    mold
• "流动模型" 英文翻译 :    flow model
• "流动模型法" 英文翻译 :    method of current flow models
• "被动模拟" 英文翻译 :    passive analog
• "表驱动模拟" 英文翻译 :    table driven simulation; table-driven simulation
• "电动模拟" 英文翻译 :    electrodynamic analogy; electrodynamicanalogy
• "气动模拟" 英文翻译 :    pneumatic analogue
• "全动模拟机" 英文翻译 :    ffs full flight simulator; full flight simulator
• "液动模拟" 英文翻译 :    fluid flow analog; fluid-flow analog; hydrodynamic analogy
• "运动模拟" 英文翻译 :    motion simulation
• "振动模拟器" 英文翻译 :    vibration simulator
• "自驱动模拟" 英文翻译 :    self-driven simulation
• "埃林流动模型" 英文翻译 :    eyring model for flow
• "艾林流动模型" 英文翻译 :    eyring model for flow
• "对流流动模型" 英文翻译 :    convection flow model
• "多室流动模型" 英文翻译 :    compartment flow model
• "分相流动模型" 英文翻译 :    separated flow model
• "混相流动模型" 英文翻译 :    miscible flow model
• "连续流动模型" 英文翻译 :    continuous flow model
• "流动模型试验" 英文翻译 :    model flow test
• "脉冲流动模型" 英文翻译 :    pulsatile flow model

• Simulation of fluid flow of an agitated thin - film evaporator
  薄膜蒸发器内流体流动模拟
• The nonlinear flow simulation using double permeability model in deformed media
  变形介质双渗模型非线性流动模拟
• Application of the flowing simulation technology in injection molding design
  流动模拟技术在注塑成型设计中的应用
• Standard guide for defining boundary conditions in ground - water flow modeling
  地下水流动模拟中确定边界条件的标准导则
• Simulation of separated flows for the nrel airfoil using anisotropic two - equation turbulence models
  非线性双方程湍流模型用于翼型分离流动模拟
• Simulation of 3d flow field of melt conveying in the single screw extruder under vibration force field
  振动力场下单螺杆挤出机中聚合物熔体三维流动模拟
• Now , the theory of two - phase flow and granular model have become the focus of filling simulation
  目前两相流理论和颗粒模型正成为mim充模流动模拟的热点。
• Finally the fluid simulation is performed . and the results can be the basis for optimizing design of helical intake port
  最终用cfd软件对气道进行流动模拟计算，为设计优化提供判断依据。
• A method based on flowing simulation to automatically realize the flowing balance of the multi - cavity injection mould was introduced
  介绍了一种基于流动模拟自动实现多型腔注射模流动平衡的方法。
• The methods and feasibilities by which the filling simulation software of plastic injection molding can be adjusted for mim have been discussed
  探讨了修改塑料注射成型充模流动模拟软件作为金属注射成形充模流动模拟的可能性及方法。