润滑点的英文

发音:

"润滑点"怎么读用"润滑点"造句

英文翻译手机版

lubricated point
lubricating point
lubrication points
oil site
oiling point

"润滑"英文翻译 lubricating; lubrication; lu ...
"点"英文翻译 drop
"润滑点说明图" 英文翻译 : lubrication chart; oiling chart
"润滑点指示图" 英文翻译 : lubrication point chart
"打滑点" 英文翻译 : point of slippage
"光滑点" 英文翻译 : slick spot
"起滑点" 英文翻译 : ftarting point
"起滑点名" 英文翻译 : call to the start
"着陆下滑点" 英文翻译 : approach aiming point
"后滑点冰停止" 英文翻译 : backtoe scratch
"润滑" 英文翻译 : [机械工程] lubricating; lubrication; lubricate 飞溅润滑法 splash lubrication; 润滑材料 lubricant; 润滑层 lubricating layer; 润滑膏 cup grease; 润滑冷却液 metalworking coolant; 润滑器 lubricator; 润滑作用 lubrication; lubrication action; 润滑装置 lubricating device
"润滑；润滑法；注油" 英文翻译 : lubrication
"润滑袋；润滑罩" 英文翻译 : grease boot
"润滑脂润滑" 英文翻译 : grease lubrication
"润滑的润滑剂，润滑油" 英文翻译 : lubricant
"泵润滑" 英文翻译 : pumlubrication
"坏润滑" 英文翻译 : power lubrication
"季润滑" 英文翻译 : quarterly lubrication
"加油，润滑" 英文翻译 : oiling
"力润滑" 英文翻译 : hydrodynamic lubrication
"铃润滑" 英文翻译 : fluid lubrication
"润滑，注油" 英文翻译 : lubrication
"润滑槽" 英文翻译 : lubricating groove; lubrication groove
"润滑层" 英文翻译 : lubricant carrier; lubricant film; lubricating layer; lubricatinglayer
"润滑车" 英文翻译 : greasing truck

例句与用法

Let ' s get you nice and lubricated
让你再润滑点
A pressure transducer was set up in this system to realize pressure control in main lines and adjustment of pump operating time ; the distributors were designed to accomplish grease storage in fixed quantity and transport them into all lubricating points ; the single chip microcomputer was utilized to control interval lubrication and realize auto - lubricating or fault alarm
系统通过设置压力传感器实现主油路的压力控制和油泵工作时间的自动调节，通过配油器实现定量储油和将油脂输送至各润滑点，通过电子监控器设定加脂间隔时间，实现自动加脂与故障报警。
The preparing work before test run : first organize test run guide group consisted of supply party , demand party and installation party to check the installed qualified equipment ( machine , electricity , liquid , gas ) in an all - round way to see that circuit , water - way , gas - way and oil - way are switched on ; that all fastener , bolts and nuts are tight ; that all lubricating points and cooling points are put in position
试运转前的准备工作：首先应组织有关（供方、需方、安装）等单位参加的试车领导小组，对已安装合格的设备（机、电、液、气）进行全面的检查，电路、水路、气路、油路是否接通，所有设备的紧固件、螺栓、螺母等是否拧紧，各润滑点和冷却点是否到位。