焊接回路的英文

• welding circuit
• welding return

• "焊接"英文翻译    weld; welding; soldering; se ...
• "回路"英文翻译    return circuit; return; loop ...
• "近接回路" 英文翻译 :    oining circuit
• "焊接回转台" 英文翻译 :    floor turnable positioner; floor turntable positioner
• "本安连接回路" 英文翻译 :    associated circuit of intrinsically safe system
• "数据链路连接回路" 英文翻译 :    data-link-attached loop
• "边不相接回路的并集" 英文翻译 :    edge disjoint circuit union
• "回路" 英文翻译 :    [电学] return circuit; return; loop tank; circuit; contour; mesh circuit◇回路电容 tank capacitance; tankage; 回路方程 loop equation; 回路分析法 loop analysis; 回路增益 loop gain
• "间接回波" 英文翻译 :    indirect echoes
• "间接回忆" 英文翻译 :    indirect recall
• "直接回火" 英文翻译 :    direct teemingtopouring direct tempering; direct tempering
• "直接回家" 英文翻译 :    go right home
• "直接回扣" 英文翻译 :    immediate rebate
• "直接回流" 英文翻译 :    direct recoup
• "直接回授" 英文翻译 :    direct feedback
• "直接回水制" 英文翻译 :    direct return system; direct-return system
• "直接回忆" 英文翻译 :    direct recall
• "直接回应" 英文翻译 :    direct-response
• "焊接" 英文翻译 :    weld; welding; soldering; seal; sealing; sealing-in; shutting together 电弧焊接 (electric) arc welding; 焊接材料 welding material; 焊接操作 welding operation; 焊接车间 welding shop; 焊接点 point of weld; soldering point; pad; 焊接电极 [冶金学] welding electrode; 焊接电流 [电工] welding current; 焊接电源 source of welding current; welding source; 焊接方法 welding method; 焊接缝 flog; soldering joint; 焊接工 weldor; 焊接工艺 bonding technology; 焊接机 bonding machine; soldering machine; 焊接检查 welding inspection; 焊接件 weldment; 焊接强度 weld strength; 焊接缺陷 weld defect; 焊接熔池 welding pool; 焊接深度 depth of weld; 焊接温度 welding temperature; 焊接质量 welding quality
• "氨的间接回收" 英文翻译 :    indirect ammonia recovery
• "氨直接回收法" 英文翻译 :    direct ammonia recovery
• "接回电力供应" 英文翻译 :    reconnection of supply
• "直接回镜检查" 英文翻译 :    direct pharyngoscopy
• "主回路；一回路" 英文翻译 :    primary coolant circuit
• "氨气直接回收法" 英文翻译 :    direct ammonia recovery

• Transitional feature of the arc and metal droplet in the welding process with steam shielded arc is investigated by means of analysing the waveforms of welding voltage and current under different welding regimes and it is found that there are two types of arc process behavor ? " arc starting - arc blowing out - short - circuiting " and " arc - starting - short - circuiting " . under the condition of constant diameter of welding wire and its feeding speed , the arc process behavor can be changed by adjusting the inductance of welding circuit as well as the voltage of power supply . if arc process behaves as alternative process of " arc starting - arc blowing out - short - circuiting " with minimum time duration of arc blowing out and maximum frequency of short - circuit transition , the welding process will be stable with less spatter and smooth weld bead
  通过分析不同焊接规范下的焊接电压和电流的波形.研究了水蒸气保护下电弧及熔滴过渡的特点，发现其电弧过程行为有“燃弧?熄弧?短路”和“燃弧?短路”两种形式.在焊丝直径和送丝速度一定的情况下，通过调节焊接回路中的电感量和电源电压，可以改变电弧的过程行为形式.若电弧过程呈“燃弧?熄弧?短路”交替进行，并且熄弧时间最短时，短路过渡频率最高，在这种情况下，飞溅小，焊道成型好，焊接过程稳定