焊接处的英文

• commissure
• weld

• "焊接"英文翻译    weld; welding; soldering; se ...
• "处"英文翻译    place
• "支撑焊接处" 英文翻译 :    reference junction
• "下侧梁焊接处" 英文翻译 :    b.s.r welding
• "接处" 英文翻译 :    join
• "通过焊接连接处的开孔" 英文翻译 :    openings through welded joints
• "对接处" 英文翻译 :    commissure
• "胶接处" 英文翻译 :    weld
• "接处物" 英文翻译 :    inoculum
• "紧接处" 英文翻译 :    fit
• "连接处" 英文翻译 :    commissure; joining
• "邻接处" 英文翻译 :    adjoiner
• "嵌接处" 英文翻译 :    scarf
• "熔接处" 英文翻译 :    shut
• "焊接" 英文翻译 :    weld; welding; soldering; seal; sealing; sealing-in; shutting together 电弧焊接 (electric) arc welding; 焊接材料 welding material; 焊接操作 welding operation; 焊接车间 welding shop; 焊接点 point of weld; soldering point; pad; 焊接电极 [冶金学] welding electrode; 焊接电流 [电工] welding current; 焊接电源 source of welding current; welding source; 焊接方法 welding method; 焊接缝 flog; soldering joint; 焊接工 weldor; 焊接工艺 bonding technology; 焊接机 bonding machine; soldering machine; 焊接检查 welding inspection; 焊接件 weldment; 焊接强度 weld strength; 焊接缺陷 weld defect; 焊接熔池 welding pool; 焊接深度 depth of weld; 焊接温度 welding temperature; 焊接质量 welding quality
• "t-u连接处" 英文翻译 :    t-u junction
• "电线搭接处" 英文翻译 :    tap
• "附接处理机" 英文翻译 :    processor attached; processor, attached
• "附接处理器" 英文翻译 :    attached support processor asp; attached support processor, asp
• "公铁交接处" 英文翻译 :    co ection; connection
• "交接处理" 英文翻译 :    hand shaking
• "交接处心律" 英文翻译 :    junctional rhythm
• "接处电钟" 英文翻译 :    contact making clock
• "连接处理" 英文翻译 :    connecting processing
• "链接处理" 英文翻译 :    link process

• Slag, blowholes, and paint on unfused regions were observed at the welded junctions .
  在焊接处看到了夹渣，气孔及未熔透区的油漆。
• The joint shall be used spot welding with 10spots as per configuration below
  这个接合处将被使用在每10个结构点下的焊接处。
• The welding is so smooth that you can hardly see where the sections of pipe are joined together
  焊接处如此平滑，你几乎看不出是哪部分管道被焊接在一起了。
• Over - application of zss010 will result in increased levels of weld fume on cutting and welding , and will also increase the porosity of the welds
  如果涂覆过厚，切割和焊接时会产生大量的焊烟，并增加焊接处的孔隙。
• The bracket and vertical column of cable tray will be installed by welding or expansion bolt of the basement . the welding place treatment will be done by painting
  桥架的立柱、托臂等支架可与基础预埋件焊接固定，也可采用膨胀螺栓固定，对于现场焊接处一定要做好防腐处理，通常由用户现场涂刷防腐漆。
• Brushed stripe coating to all areas such as corners . edges , welds . small brackets , bolts , nuts . rivet - s . and interstices , before spraying application of each coat , to ensure that these areas have at least the minimum specified film thickness
  在涂抹新涂层前，应刷掉所有区域的麻纹，比如各角落、边缘、焊接处、小托架、螺钉、螺帽、铆钉和裂缝，保证这些区域至少达到价格的最低膜厚度。
• And the finite element method ( fem ) was used to simulate the stress and deformation of the outer casing and the bearing chock . on the basis of the experiments and fem analysis , the strength and fatigue lifetime , the interaction of creep and fatigue lifetime , the creep lifetime of outer casing and bearing chock have been analyzed , at the end of trail , sem analyses of failure section has been conducted
  同时对航空发动机燃气涡轮外机匣和轴承座进行了有限元模拟计算，得到外机匣和轴承座的焊接处的强度和变形情况的模拟结果。根据试验数据和有限元的计算结果，对发动机燃烧室外机匣和轴承座两种结构(包含焊缝)进行静强度分析、疲劳寿命分析、蠕变寿命分析、蠕变疲劳交互作用寿命分析以及断口的金相分析。
• It is very popular to be used for the welding of orbital tube , pipe , very small parts , short welding cycles and also where a specific number of welds are called and then the electrode is to be replaced . cerium tungsten electrode , tungsten cerium electrodes , w - ce electrode , ce - w electrodes , tungsten electrode , tungsten
  钨铈并不适合于高电流条件下的应用，因为在这种条件下，氧化物会快速的移动到高热区，即电极焊接处的顶端，这样对氧化物的均匀度造成破坏，因而由于氧化物的均匀分布所带来的上述好处将不复存在

• 焊接处的俄语：pinyin:hànjiēchù спай