焊接时间的英文

• soldering time
• weld interval
• weld period
• weld time
• welding interval
• welding period

• "焊接"英文翻译    weld; welding; soldering; se ...
• "时间"英文翻译    time; hour
• "焊接时间率" 英文翻译 :    arcing time factor
• "焊接时间间隔" 英文翻译 :    weld interval
• "多脉冲焊接时间控制器" 英文翻译 :    multiple-impulse weld timer
• "同步焊接时间继电器" 英文翻译 :    synchronous weld timer
• "序列焊接时间调节器" 英文翻译 :    sequence weld timer
• "拆接时间" 英文翻译 :    disconnecting time
• "换接时间" 英文翻译 :    shifting time
• "接时间段" 英文翻译 :    after 7:00 in five minutes between among betweenen
• "接时间选路" 英文翻译 :    time-dependent routing
• "拒接时间" 英文翻译 :    access denial time
• "跨接时间" 英文翻译 :    jumtime
• "连接时间" 英文翻译 :    co ect time; connect time; connecting time; link time; logged on time; the time in days，hours and minutes you are connected to the net; tie-time
• "链接时间" 英文翻译 :    link time
• "桥接时间" 英文翻译 :    bridging time
• "粘接时间" 英文翻译 :    klebezeit bonding time
• "转接时间" 英文翻译 :    transfer time; transit time
• "电阻熔接时间" 英文翻译 :    resistance welding time
• "换机衔接时间" 英文翻译 :    connecting time
• "通过时间, 转接时间" 英文翻译 :    transit time
• "后面不接时间状语" 英文翻译 :    be about to
• "遥程系统连接时间" 英文翻译 :    connect time remote system
• "远程系统连接时间" 英文翻译 :    remote system connect time
• "直接时间研究法" 英文翻译 :    direct time study approach

• Welding time adopts circle style counting control
  焊接时间均彩霞周波调式计数控制。
• The welding time and weld quality is guaranteed by international purchased welder
  采用国外引进焊机确保钢带焊接时间和焊接质量。
• Feature : automatoc controlling the time of welding , extensive limit of adjustment , simple and stable structure easy operation
  特点：能自动控制焊接时间，调节范围大，结构简单可靠，操作方便。
• When soldering the electrolytic capacitor , the soldering time should never be permitted over 10 seconds , and for 260 ? c of the soldering temperature
  在焊接电解电容器时，其焊接时间和焊接温度不应超过10秒钟及260摄氏度。
• Direct connect vias conduct so much heat away from the pin and into the plane that high temperature or long soldering time may be required to complete the joint - thermal damage could occur to both the board and the component from soldering or desoldering
  在焊接时，直接连接的过孔会通过引脚把大量的热传导至内电层，因此完成焊接就需要很高的温度或者延长焊接时间，这就会导致在焊接或拆焊时发生电路板或元件的损坏。
• The planeness and integrality of the flier - plate were ensured effectively by exerting restrictive pressure , controlling heating and cooling rate , lowering welding temperature or reducing welding time as much as possible , etc . theoretical model of creating quasi - isentropic compression via 93w - ofc - tc4 - a1 - mb2 system flier - plate with graded wave impedance was established , and numerical simulation of the impact process was then carried out
  采取施加外部机械力、控制升降温速率以及尽量降低焊接温度或减少焊接时间(防止脆性金属间化合物的过度增长)等措施，确保了焊接接头的平整性和界面结构的完整性。建立起梯度飞片击靶的理论模型，对93w - ofc - tc _ 4 - al - mb _ 2系波阻抗梯度飞片的击靶过程进行了数值模拟计算。

• 焊接时间的日语：ようせつじかん