焊缝厚度的英文

• actual weld throat thickness
• actual weld-throat thick-ness
• seam welding throat thickness
• throat depth/ throat thickness
• weld thickness
• weld-throat thickness depth

• "焊缝"英文翻译    soldering seam; weld bead; w ...
• "厚度"英文翻译    thickness; land
• "角焊缝厚度" 英文翻译 :    throat depth of fillet weld; throat depth (thickness) of fillet weld
• "焊缝厚度不足" 英文翻译 :    insufficient throat
• "实际焊缝厚度" 英文翻译 :    actual throat depth
• "有效焊缝厚度" 英文翻译 :    effective throat depth
• "最大焊缝厚度" 英文翻译 :    maximum throat depth
• "焊缝厚度焊接厚度" 英文翻译 :    throat thickness
• "实际角焊缝厚度" 英文翻译 :    actual throat
• "水平灰缝厚度" 英文翻译 :    thickness of mortarat bed joint; thin shell
• "焊缝表观厚度" 英文翻译 :    apparent weld throat thickness
• "焊缝计算厚度" 英文翻译 :    effective throat thickness; theoretical throat
• "焊缝理论厚度" 英文翻译 :    theoretic throat depth
• "焊缝设计厚度" 英文翻译 :    design throat thickness
• "焊缝实际厚度" 英文翻译 :    actual throat
• "焊缝有效厚度" 英文翻译 :    effective throat thickness
• "焊缝最小厚度" 英文翻译 :    minimum weld throat thickness
• "（角）焊缝计算厚度，有效厚度" 英文翻译 :    effective throat
• "角焊缝实际厚度" 英文翻译 :    actual throat of a fillet weld
• "角焊缝有效厚度" 英文翻译 :    effective thickness of fillet weld; elastic analysis scheme
• "实际焊喉深度 焊缝实际厚度" 英文翻译 :    actualthroat
• "焊缝" 英文翻译 :    soldering seam; weld bead; weld joint; weld seam; welded joint; welded seam; welding seam; seal; sealing; sealing run; shut; brazing seam
• "厚度" 英文翻译 :    thickness; land (刀刃的)
• "缝厚能力测试方法" 英文翻译 :    household sewing machines determination of sewing capacity
• "总厚度，全厚度" 英文翻译 :    full thickness

• When the welding current is added , the quality of heat of the arc will increase , so both the volume of molten puddle and the depth of arc crater will all increase , and the weld depth will increase when the weld is cooling
  焊接电流增加时，电弧的热量增加，因此熔池体积和弧坑深度都随电流增加，所以冷却下来后，焊缝厚度就增加。
• The welding speed have evident effection on weld depth and weld width , when welding speed is added , both weld depth and weld width will decrease , for the inputed heat per time is limited
  焊接速度对焊缝厚度和焊缝宽度有明显的影响，当焊接速度增加时，焊缝厚度和宽度都大为下降，这是因为焊接速度增加时，焊缝中单位时间内输入的热量减少。
• Weld positioning under load without installation , seam thickness of the seam thickness of not less than two - thirds of the design , not to exceed 8 mm , should not be less than 25 mm in length weld , located in welds inside
  安装定位焊缝不需承受荷载时,焊缝厚度不少于设计焊缝厚度的2 / 3 ,且不大于8 ? ,焊缝长度不宜小于25 ? ,位置应在焊道内.安装焊缝全数外观检查,主要的焊缝应按设计要求用超声波探伤检查内在质量.上述检查均需做出记录
• Sonic new ideas and views were proposed , such as regulation on general welding procedure qualification and its method of application , welding procedure qualification between heat exchange tube and tube sheet assessmented by the thickness of fillet weld , and so on
  本文还首次提出一些新思路、新观点，如母材、焊材分类细则以及标准以外材料分类要有分类报告佐证；通用的焊接工艺评定规定及使用方法；换热管与管板的焊接工艺评定是评定角焊缝厚度；气瓶焊接工艺评定是两个类型评定的结合，也可以分别评定。

• 焊缝厚度的日语：のど厚さ ふところ深さ のど厚 のどあつ ふところぶかさ のどあつさ