生坯的英文

发音:

"生坯"怎么读"生坯"的汉语解释用"生坯"造句

英文翻译手机版

green body
green compact
green ware body
green-ware

"生"英文翻译 give birth to; bear
"坯"英文翻译 base
"生坯间" 英文翻译 : green house
"生坯块" 英文翻译 : green briquette
"生坯间(陶)" 英文翻译 : green house
"生坯孔隙度" 英文翻译 : green porosity
"生坯密度" 英文翻译 : green density; unfired density
"生坯强度" 英文翻译 : green strength
"生坯强度(陶)" 英文翻译 : green strength
"生坯丝绸" 英文翻译 : raw silk fabric
"生坯性能" 英文翻译 : green properties
"生坯压坯" 英文翻译 : green compact
"生坯直径" 英文翻译 : green diameter
"生坯周转区" 英文翻译 : raw material block
"生坯状态" 英文翻译 : green state
"生坯抗剪强度试验" 英文翻译 : green shear strength test
"生坯电力纺绣花台布" 英文翻译 : raw habotai embroidered table cloth
"生佩积" 英文翻译 : green volume
"生配子有丝分裂" 英文翻译 : gametogenetic mitosis
"生泡试验" 英文翻译 : bubble test
"生泡掺合料" 英文翻译 : foam forming admixture
"生泡" 英文翻译 : head formation

例句与用法

Raw rubber or unvulcanized compounds . determination of green strength
生橡胶或硫化化合物.生坯强度测定
Metallic powders - determination of green strength by transverse rupture of rectangular compacts
金属粉末生坯强度的测定矩形压坯横向断裂法
Test methods for pore size distribution of fine ceramic green body by mercury porosimetry
用水银孔隙度测定法测定细陶瓷生坯的气孔尺寸分布的试验方法
The densification of glass bead was studied with different green densities at different temperature to burn out the binde
摘要用不同密度的玻璃绝缘子生坯，在不同温度下排蜡，研究了玻璃绝缘子的致密化。
Low sheet resistance and good matching between substrate and paste are the principal requirements for conductor paste in multi - layer cofire substrate
共烧导带浆料与aln生坯之间的烧结应力是造成基板失效的原因。
We need to start their sintering at same temperature and to ensure conductor paste and green - sheet ceramic bodies have the same shrinkage rate
为了消除二者之间的烧结应力，共烧导带浆料与aln生坯必须同时进入烧结状态，具有相同的收缩特性。
The relative density of the powder flan was well controlled by design of the press process . the property of the flan was good
本文通过压制工艺的设计，有效的控制了mo - cu粉末生坯的压制密度，得到了质量良好、相对密度符合预先设计要求的mo - cu粉末压制生坯。
The results show that more green density causes more densification but less linear shrinkage and higher burnout temperature causes more densification but less densification rate
发现生坯密度越大，排蜡后绝缘子线收缩越小，致密化程度大大提高；随排蜡温度升高，绝缘子致密化程度增大，致密化速率减小。
To insure more densification but deformation of glass beads , the green density should be increased , and the burnout temperature of binder should be below the toplimit of transformation temperature
为保证绝缘子获得较高致密度而不变形，应尽量提高生坯密度，温度同时排蜡应低于该种玻璃的转变温度上限。
In this paper , the mechanical alloy technology ( ma ) was adopted . through the designing and optimizing of the ma technology and liquid phase sinter technology , the new electrician alloy - mo - cu was made
本文采用粉末冶金的非平衡制备高新技术?机械合金化法，通过机械合金化工艺、粉末生坯压制工艺和液相烧结工艺的设计与优化，制备出了mo - cu高比重合金。