砂轮转速的英文

• grinding wheel speed
• speed of grinding wheel

• "砂轮"英文翻译    emery cutter; knife grinder; ...
• "转速"英文翻译    speed; revolution; rotation ...
• "实际砂轮转速" 英文翻译 :    actual wheel speed
• "轮转速" 英文翻译 :    wheel eed; wheel speed
• "车轮转速计" 英文翻译 :    trocheameter
• "传动轮转速" 英文翻译 :    drive-wheel speed
• "从动轮转速" 英文翻译 :    secondary speed
• "皮带轮转速" 英文翻译 :    pulley speed
• "涡轮转速" 英文翻译 :    secondary speed; speed; turbine; turbine speed
• "机轮转速减慢" 英文翻译 :    wheel deceleration
• "涡轮转速调节" 英文翻译 :    turbine speed control
• "自由涡轮转速" 英文翻译 :    free turbine speed
• "车轮转速传感器" 英文翻译 :    wheel speed sensor; wheel-speed sensor
• "机轮转速传感器" 英文翻译 :    wheel speed transducer
• "摩擦轮转速计数器" 英文翻译 :    friction wheel speed counter
• "右后轮转速传感器" 英文翻译 :    right rear wheel-speed sensor
• "右前轮转速传感器" 英文翻译 :    right front wheel-speed sensor
• "左后轮转速传感器" 英文翻译 :    left rear wheel-speed sensor
• "左前轮转速传感器" 英文翻译 :    left front wheel-speed sensor
• "车轮转速传感器与脉冲轮" 英文翻译 :    wheel-speed sensor & pulse wheel
• "后轮转速传感器脉冲轮" 英文翻译 :    pulse wheel, rear wheel-speed sensor
• "前轮转速传感器脉冲轮" 英文翻译 :    pulse wheel, front wheel-speed sensor
• "轮转" 英文翻译 :    rotate; [计算机] round robin 轮转计 trocheameter; odometer; 轮转印刷机 rotary machine; rotary press; [印刷] rotary printing- machine
• "砂轮" 英文翻译 :    [机械工程] emery cutter; knife grinder; grindstone; buzzer; abrasion wheel; carborundum wheel; emery wheel; sandstone disk; stone wheel; grinding wheel◇砂轮电机 grinding wheel drive motor; 砂轮机 grinder; 砂轮截断机 cut-off grinder; 砂轮锯 abrasive cutoff saw; 砂轮磨工 jiggerman; 砂轮磨光机 sander; 砂轮切割机 abrasive wheel cutting machine; 砂轮头 wheelhead; 砂轮修正器 truer; 砂轮整形 emery wheel dressing; grinding wheel truing
• "燃气轮转速反馈数字电子燃油控制" 英文翻译 :    nbdec speed based digital electronic control

• The results show that , when increasing the feed rate of the grinding wheel , decreasing the rotating speed of the wafer chuck table and using coarser grit grinding wheel , the material removal rate in the wafer rotating grinding increase , the feed rate of the grinding wheel has greater influence on the material removal rate ; when suitably increasing the rotating speed of the grinding wheel , decreasing the feed rate of the grinding wheel and using finer grit grinding wheel , the wafer surface roughness can be reduced ; there exists a critical rotating speed of the grinding wheel ( about 2300rpm ) , beyond which the material removal rate evidently decreases and the spindle motor current and wafer surface roughness steeply increase ; when the grit size of the grinding wheel is finer than # 2000 , the material removal rate decreases and the wafer surface roughness has no obvious improvement
  研究结果表明，增大砂轮轴向进给速度和减小工件转速，采用粗粒度砂轮有利于提高磨削矽片的材料去除率，砂轮轴向进给速度对材料去除率的影响最为显著；适当增大砂轮转速，减小砂轮轴向进给速度，采用细粒度砂轮可以减小磨削表面粗糙度；在其它条件一定的情况下，砂轮速度超过一定值会导致材料去除率减小，主轴电机电流急剧增大，表面粗糙度变差；采用比# 2000粒度更细的砂轮磨削时，材料去除率减小，矽片表面粗糙度没有明显改善。
• By using a wafer - rotating grinding machine , the influence of the main process factors including grit size of diamond grinding wheel , rotating speed of the wafer chuck table , rotating speed and the down feed rate of the cup grinding wheel on the material removal rate , spindle motor current and wafer surface roughness in grinding large size wafer are experimentally investigated
  摘要利用基于自旋转磨削原理的矽片超精密磨床，通过试验研究了砂轮粒度、砂轮转速、工件转速及砂轮进给速度等主要因素对材料去除率、砂轮主轴电机电流以及磨削后矽片表面粗糙度的影响关系。