磨粒磨损的英文

• abrasive wear

• "磨"英文翻译    mill; millstones
• "磨损"英文翻译    wear and tear; abrasive wear ...
• "磨粒磨损试验机" 英文翻译 :    grain-abrasion testing machine
• "磨轮颗粒磨损体积" 英文翻译 :    volume of wheel grain wear
• "磨粒" 英文翻译 :    abrasive grains; abrasive particle; grit; mill grain
• "磨粒度" 英文翻译 :    grid size
• "研磨粒" 英文翻译 :    abrasive grain
• "磨损" 英文翻译 :    wear and tear; abrasive wear; abrase; abrade; detrition; wear; scuff; wear-out; fray; battering; abrade wear; abrasion; attrition wear; defacement; excoriate; foreworn; wear down; wearing; wornout 我的鞋跟给磨损了。 the heels of my shoes have (been) worn down. 这辆卡车基本上没有什么磨损。 the truck shows scarcely any sign of wear and tear.; 磨损程度 degree of wear; 磨损度 abradability; 磨损腐蚀试验 erosion corrosion test; 磨损检验 examine for wear; 磨损留量 wear allowance; tear-and-wear allowance; 磨损试验 [土] attrition test; abrasion test; 磨损试验机 abrasion tester; abrasive wear testing machine; wear-test machine; 磨损数据 wear data; 磨损速度 rate of wear; 磨损系数 coefficient of waste; coefficient of wear; wear coefficient; mortality factor; 磨损作用 abrasive action
• "谷粒磨粉机" 英文翻译 :    grain grinder
• "颗粒磨耗" 英文翻译 :    particle attrition
• "微粒磨碎机" 英文翻译 :    micro-pulverizer
• "细粒磨料" 英文翻译 :    fine abrasive
• "粗粒；磨粒粒度" 英文翻译 :    grain grit
• "钢砂磨粒" 英文翻译 :    steel shot abrasive
• "固结磨粒" 英文翻译 :    fixed grain
• "磨粒；磨料粒度" 英文翻译 :    abrasive grain
• "磨粒大小" 英文翻译 :    abrasive grain sizes
• "磨粒的硬度" 英文翻译 :    hardness of grain
• "磨粒粒度" 英文翻译 :    grain grit
• "磨粒图谱" 英文翻译 :    atlas of wear particle
• "研磨粒度" 英文翻译 :    grind size
• "中等磨粒" 英文翻译 :    medium-grain
• "粉碎器细粒磨碎机" 英文翻译 :    pulverizer
• "中等晶粒 中等磨粒 中粒" 英文翻译 :    medium-grain
• "最好的研磨粒度" 英文翻译 :    mesh of grind

• Abrasive wear may be defined as damage to a surface by a harder material .
  磨粒磨损可定义为较硬的材料对一个表面的破坏。
• Development of abrasive wearability surfacing electrode based on tic - vc
  的抗磨粒磨损堆焊焊条
• Analysing the wear mechanism of abrasive . adhesive wear . 2
  对磨粒磨损和粘着磨损的磨损机制进行分析。
• The alloy has good thermal stability ; the fracture mechanism of the alloy is not obvious to si particle size but closely relate to the dis
  48 ；而300ac时磨损量为14 zing儿，摩擦系数为0 72 ） ，其室温磨损机制以磨粒磨损为主。
• The method can be adopted to research micro dynamic behavior and changing of friction surface and to show mechanism of abrasive wear
  为研究摩擦表面上的微观动态行为与变化，认识磨粒磨损机理，提供了一种基于微观数值模拟的途径和方法。
• Microscopic analysis of the abrasion surface indicated that the wear mechanism of composites and matrix alloy included sticking abrasion and grindrng - particle abrasion on the materials
  磨损表面微观分析表明，复合材料的磨损过程是粘着磨损和磨粒磨损两种机制共同作用的结果。
• Especially , it also registered a lower wear rate of the polymer counterpart compared with ti6a14v alloy . the worn surfaces of the tested samples were observed with a scanning electron microscope , as an effort to analyze the wear mechanisms
  Dlc膜的减摩机理与其表面高硬度含氢非晶态碳膜结构和成分有关，磨损形式主要是轻微的磨粒磨损。
• In order to analyze a micro cutting process of abrasive wear by means of molecular dynamics simulation , the principle , model and solving algorithm of molecular dynamics simulation of micro cutting process were discussed
  摘要针对磨粒磨损中微观切削过程，研究了分子动力学模拟的基本原理、磨粒微观切削过程的分子动力学模拟模型和数值模拟势法。
• In the dry sliding experiments of composites , friction coefficients decrease with the loads . plastic deformation happens in the worn surface where the element of fe is found , so pam microfibrils support part of the load and prevent the further deformation
  低速低载时，试样磨损表面出现塑性变形，在复合材料的磨损表面还发现fe元素的存在，表明pam微纤承受了部分载荷，阻止了基体的粘着转移，此时磨损机理为磨粒磨损和粘着磨损。
• Under a constant applied load and sliding speed , the wear rate of cu - nanosized tib2 in - situ composites was increased with increasing the electric current . the predominant electric wear mechanisms of the cu - nanosized tib2 in - situ composites are abrasive wear and arc erosion
  在一定载荷和滑动速度下，随电流的增加， cu -纳米tib2原位复合材料的磨损率增加， cu -纳米tib2原位复合材料的电接触滑动磨损机制主要为磨粒磨损和电侵蚀磨损。