膛压的英文

• bore pressure
• chamber pressure
• gun pressure
• pressure in chamber

• "膛"英文翻译    chest; thorax
• "压"英文翻译    press; push down; hold down; ...
• "膛压计" 英文翻译 :    pressure gage
• "膛压仪" 英文翻译 :    chamber pressure gauge
• "高膛压底火" 英文翻译 :    high barrel pressure primer
• "火炮膛压" 英文翻译 :    bore pressure of gun
• "炉膛压力控制" 英文翻译 :    fdc: furnace draft control
• "钻孔空膛压辊" 英文翻译 :    chamber-bored roll
• "炉膛压力调节器" 英文翻译 :    furnace pressure controller
• "气压计，压强计；(火炮药室内的)膛压表。" 英文翻译 :    pressure gage; pressure gauge
• "膛线枪炮" 英文翻译 :    rifle
• "膛线起点" 英文翻译 :    origin of rifling
• "膛炸" 英文翻译 :    bore premature
• "膛线炮管" 英文翻译 :    rifled barrel; rifled bore
• "唐" 英文翻译 :    Ⅰ名词1.(唐朝) the tang dynasty (618-907) 唐诗 tang poetry2.(姓氏) a surname 唐甄 tang zhenⅡ形容词1.(虚夸) exaggerative; bombastic; boastful 唐大无验 too exaggerative to check2.(空; 徒然) in vain; for nothing 功不唐捐。 all efforts are not made for nothing
• "膛线炮" 英文翻译 :    rifled cannon; rifled gun
• "唐 柏利" 英文翻译 :    felton perry
• "膛线拉刀" 英文翻译 :    rifling head

• The result show , the new technology can improve propeller ' s velocity while not adding chamber ' s pressure . 4
  比较结果表明，串联多药室火炮可以在不增加膛压的情况下达到提高弹丸初速的目的。
• During the course of developing and using high ballistic performance artillery with high exit velocity , high chamber pressure and high loading density , there were many accidents of breech blow
  在高初速、高膛压和高装填密度为特征的高弹道性能火炮的研制与使用过程中，曾经出现过多次膛炸事故。
• For more than a hundred years , the method of plastic deformation for measuring pressures has been the main means to test the chamber pressure of conventional weapons because of its advantages of reliability , convenience and low price
  塑性变形测压法具有工作可靠、使用方便、成本低廉等突出的优点，一百多年来，一直是常规武器膛压检验的主要技术手段。
• On the similitude artillery , 7 items of shooting tests were proceeded . these items included : muzzle velocity of projectile , pressure of gases , recoil force , efficiency of muzzle brake , muzzle shockwave , dynamic stress , stability
  在模型炮上进行了7个射击实验项目，实验项目包括：初速、膛压、后坐阻力、炮口制退器效率、炮口冲击波、动态应力、稳定性。
• In our country the method of pressure - measuring with copper cylinders adopts the system of static calibration on the whole . the serious static - dynamic discrepancy will be caused when the copper cylinders statically calibrated are used to measure the dynamic chamber pressure
  我国的铜柱测压法基本上仍沿用静态标定体制，而静标铜柱用于动态膛压测量会产生严重的静动差。
• By researched and analyzed , it was found that grain fracture had close relation with charge design safety of guns . grain fracture can lead to pressure abnormity in chamber . particularly in the condition of low temperature , it was the main cause leading to chamber blow
  经研究分析，火药颗粒的破碎直接影响到装药设计安全性，造成膛压异常现象，特别在低温条件下，火药破碎是引起膛炸的主要原因。
• The basic signals in the projectile test are dynamic signals such as high initial speed , high chamber pressure , high frequency response , high impact , high temperature measurand . so , the test and measurement system should have more channels , the signals are easy to be obtained , and no matter the measurand it is , the test and measurement plateau should be integrated instantly
  弹丸测试的基本信号是高初速、高膛压、高频响、高过载、高冲击、高温等诸多动态量的信号，这要求测试系统通道多、捕捉动态信号容易、搭建针对不同被测信号的测试平台快捷。
• This is the theoretical foundation for simulating the gun interior ballistic performance using the closed vessel experiment . based on the functions from closed vessel experiments , the ballistic simulation results of maximum chamber pressure , muzzle velocity and p - t curves of a 105mm gun charged with ltsc nitroamine propellant at + 50c , + 15c and - 40 environmental temperature were in good agreement with experimental data
  在密闭爆发器实验的基础上，应用可视化程序对某105mm火炮采用低温感硝胺火药在+ 50 、 + 15和- 40环境温度下的最大膛压、初速以及膛压?时间曲线进行了弹道模拟，模拟与实验结果具有较好的一致性。
• The results proved that : ( 1 ) because of the material ' s difference of primer - 9 and primer - 5 , the maximum stress of primer - 5 is larger than primer - 9 but the maximum displacement is smaller than primer - 9 . ( 2 ) because of the unrenewable shape changing of primer - 9 after impacting by the pin , it will cracking under high pressure more easily . so , the paper give the suggestion that the designer should decrease the depth of impacting by pin in the case of the primer be fired successfully
  对底- 9底火、底部被击针撞击后的第- 9底火和底- 5底火在膛压作用下分别进行了有限元数值分析，计算表明： ( 1 )底- 5底火底部击针撞击部位为火帽座，其材料为钢带，底- 9底部承受撞击部位为底火体，其材料为冷拉退火圆钢，由于材料强度不同，承受压力能力和变形能力不同：虽然在膛压作用过程中底- 5底火的最大应力值比底- 9底火的大，但底- 5底火的最大位移量却比底- 9底火的小得多。

• 膛压的俄语：pinyin:tángyā воен. давление в канале ствола