表面平整度的英文

• surface evenness
• surface smoothness

• "表面"英文翻译    surface; superficies; bounda ...
• "平整"英文翻译    level
• "度"英文翻译    surmise; estimate
• "路面平整度" 英文翻译 :    surface evenness
• "墙面平整度" 英文翻译 :    degree of plainness for wall surface; depth of compression zone
• "硅抛光片表面平整度测试方法" 英文翻译 :    test methods for surface flatness of silicon polished slices
• "表面平整" 英文翻译 :    surfacing
• "表面平整机" 英文翻译 :    surfacing machine
• "外表面平整" 英文翻译 :    mm skin smoother
• "路面平整度测定仪" 英文翻译 :    profilometer; viameter
• "路面平整度测量仪" 英文翻译 :    vialog
• "桥面平整度测定仪" 英文翻译 :    travelling-beam testing device for deck surface irregularity
• "表面不平整度" 英文翻译 :    surface irregularities; undulation
• "铺顶表面平整" 英文翻译 :    surfacing of roofing material
• "表面修整，表面平整" 英文翻译 :    surfacing
• "摊铺路面平整度试验" 英文翻译 :    paved surface evenness test
• "平整度" 英文翻译 :    flatness; planeness; temper grade
• "不平整度" 英文翻译 :    degree of irregularity; irregularity degree; roughness; slope variance; unevenness
• "不平整度仪" 英文翻译 :    roughometer
• "草坪平整度" 英文翻译 :    evenness of turf
• "钢背平整度" 英文翻译 :    backing plate flatness
• "构件平整度" 英文翻译 :    degree of plainness for structural memer; degree of plainness for wall surface
• "胶片平整度" 英文翻译 :    film flatness
• "平度，平整度" 英文翻译 :    flatness
• "平整度检验" 英文翻译 :    flatness inspection

• To enhance the surface smoothness and gloss of products
  提升制品表面平整度及光泽度。
• Test methods for surface flatness of silicon polished slices
  硅抛光片表面平整度测试方法
• Test method for photoplate surface flatness by interferometric noncontact technique
  用无触点干涉测量技术测量胶片表面平整度的试验方法
• Methods of test for masonry units - part 20 : determination of flatness of faces of masonry units ; german version en 772 - 20 : 2000 a1 : 2005
  圬工单位的试验方法.第20部分:圬工单位表面平整度测
• The adoption of fine aggregates can reduce the separation of aggregates and improve the compactness and surface smoothness of concrete of the sidewall
  配合比中用小区料作骨料，能减少骨料分离，提高边墙混凝土密实性及表面平整度。
• With increasing the inputting rf power further , the intensity of visible band emission increase , on the contrary , the intensity of uv band decreas . the surface also becomes rough as further increasing rf power
  然而随着射频功率的进一步增加，薄膜的结晶质量降低，紫外发光变弱，深缺陷发光增强，薄膜的表面平整度变差。
• Because of better conductivity , higher transparency , smoother surface and higher work function , ito ( indium tin oxide ) films are used as the transparent electrodes which are the emitting side in oled
  Oled显示器件经常采用ito膜作为有机发光的出射面和透明电极,要求ito膜可见光透过率、导电性、表面平整度以及功函数都很好。
• The structurally perfect and high - quality ba0 . 5sr0 . 5tio3 single - crystalline thin films were prepared on laalo3 and mgo substrates by pulsed laser depositioa the ba0 . 1sr0 . 9tio3 / yba2cu3o7 - heterostructure films were fabricated by pulsed laser deposition on a vicinal laalo3 su bstrates
  详尽地分析这些薄膜的衍射图样可知，薄膜都是以外延特性生长的而且晶体质量良好，但薄膜生长模式及表面平整度受沉积条件影响较大。
• In the construction industry there has always been a mismatch between the research investment and construction expenditure and this has lead the industry to proceed on a scale with an inadequate understanding of many aspects of construction , such as , deterioration mechanism for structures that has often meant that due allowance has not been made for practical repair and maintenance . however , notwithstanding this situation there have been encouraging signs that within the last twenty years the transition from the conventional materials to the more advanced materials is being spear - headed by the construction industry where over 30 of all polymers produced are now utilised in that industry
  水工建筑物是社会各建筑群体中的一类,是所在地环境的一个有机组成部分,随着经济社会的发展,水工建筑物的外观越来越受到重视.水工建筑物的外观质量控制主要在设计与施工两个环节.外观设计的质量表现在建筑物满足运行功能要求的情况下,既方便施工,又具有特色.施工的质量表现在建筑物的实施效果.常见的外观质量缺隙主要有蜂窝麻面、色泽不一、气泡偏多、表面平整度差等,应从施工工艺、建筑材料的质量等方面加以控制
• The main results are : grinding is favorable to improve surface smooth degree , while nitrided and slow deposition makes sic granules fine ; the width of coatings gap increased in order of grinding , nitrided and vacuum heat treatment , but gap defects in multilayer coatings could be removed by slow deposition ; temperature of maximum weight loss could be decrease to 600 by grinding , vacuum heat treatment or slow deposition , but it will increased to 800 after nitrided ; oxidation kinetics curves all varied with the coating modifications
  主要有：磨削改性有利于提高涂层表面平整度，氮化和慢沉积使涂层表面颗粒细化。涂层间隙宽度按磨削改性、高温氮化、真空热处理依次增大，而慢沉积可获得无面缺陷的多层涂层。磨削改性、真空热处理及慢沉积均使最大氧化失重温度点提前至600 ，而高温氮化则使最大失重点后移至800 。