角度误差的英文

• angle error
• angular error
• angular misalignment

• "角度"英文翻译    angle; the degree of angle
• "误差"英文翻译    error
• "刻度误差 分度误差" 英文翻译 :    graduationerror
• "标度误差" 英文翻译 :    scale error
• "长度误差" 英文翻译 :    error in length; error in line; linear error; size error
• "尺度误差" 英文翻译 :    scale error; size error
• "垂直度误差" 英文翻译 :    error of perpendicularity
• "分度误差" 英文翻译 :    dividing error; error of division; error of graduation; graduation error; indexing error
• "幅度误差" 英文翻译 :    amplitude error
• "高度误差" 英文翻译 :    altitude error; height error
• "加速度误差" 英文翻译 :    acceleration error
• "角速度误差" 英文翻译 :    angular rate error
• "精度误差" 英文翻译 :    trueness error
• "精确度误差" 英文翻译 :    error in exactness
• "经度误差" 英文翻译 :    longitude error; longitudinal error
• "刻度误差" 英文翻译 :    calibration error; error of graduation; error of scale; graduation error; scale errors
• "刻度误差表" 英文翻译 :    scale error card
• "量度误差" 英文翻译 :    measurement error
• "亮度误差" 英文翻译 :    brightness error; luminance errors
• "满标度误差" 英文翻译 :    full scale error
• "密度误差" 英文翻译 :    density error
• "平面度误差" 英文翻译 :    flatness error
• "平行度误差" 英文翻译 :    parallelism error
• "色纯度误差" 英文翻译 :    color purity error; colour purity error
• "速度误差" 英文翻译 :    speed course latitude error; speed error; velocity error

• Tolerance of synthetic angle
  综合角度误差
• The analyse of theary about effect on angular error for reflective characterisitic of move angular cone prism
  角度误差影响运动角锥棱镜反射特性的理论分析
• Fibre optic interconnecting devices and passive components - basic test and measurement procedures - examinations and measurements - measurement of the angular misalignment between fibre and ferrule axes
  光纤互连器件和无源元件.基本试验和测量程序.检验和测量.光纤和金属加固环轴线间角度误差的测量
• Fibre optic interconnecting devices and passive components - basic test and measurement procedures - part 3 - 26 : examinations and measurements ; measurement of the angular misalignment between fibre and ferrule axes
  光纤互连设备和无源元件.基本试验和测量程序.第3 - 26部分:检验和测量.光纤和金属加固环轴线间角度误差的测量
• In this paper , by analyzing the measuring of instantaneous speed , it was found that the main error is come from the angular measuring error , and then the method to decrease the error is given and the measurement precision is improved greatly
  摘要通过分析柴油机飞轮瞬时转速的测量误差，指出角度误差是飞轮瞬时转速的主要误差来源，从而提出了减少误差的方法，提高了瞬时转速的测量精度。
• Analyze item by item the position of unintact cycle , the running clearance of unintact cycle , locking - deform , datum dimension regulating , repeatly install , power voltage wave and marking running etc . at the same time , we give the calculating formula to calculating the running marking random error , and use it to calculate the system error of big diameter measure instrument - - datum dimension frame error , gyro - wheel diameter error , error caused by circumstance temperature , error caused by backing distance , angle error , delay error of data collecting circuit , lathe main shaft running error , workpiece install partial error
  对不完整圆的位置、不完整圆的转动间隙、锁紧变形、基准尺调整、重复安装、电源电压波动、标记转动等随机误差进行了逐项分析，并给出转动标记随机误差的计算公式。对大直径测量仪的系统误差?基准尺尺架误差、滚轮直径误差、环境温度引起的误差、后退距离引起的误差、角度误差、数据采集电路延时误差、车床主轴回转误差、工件安装偏心误差分别进行了计算，最后对误差进行合成。