许用值的英文

• allowable value

• "许"英文翻译    praise
• "用"英文翻译    40分钟跑完全程 run the course in 4 ...
• "值"英文翻译    price; value
• "疲劳许用值" 英文翻译 :    fatigue allowable
• "备用值" 英文翻译 :    backed-uvalue
• "采用值" 英文翻译 :    adopted value
• "常用值" 英文翻译 :    accepted value
• "试用值" 英文翻译 :    tentative value; test value; trial value
• "效用值" 英文翻译 :    utility value; value of utility
• "宜用值" 英文翻译 :    preferred stock value
• "应用值" 英文翻译 :    applied occurrence
• "货币效用值" 英文翻译 :    utility of money
• "经度采用值" 英文翻译 :    adopted longitude
• "年使用值" 英文翻译 :    annual usage dollars
• "平稳效用值" 英文翻译 :    stationary utility value
• "期望效用值" 英文翻译 :    expected utility
• "纬度采用值" 英文翻译 :    adopted latitude
• "引用值；基值" 英文翻译 :    fiducial value
• "预期效用值" 英文翻译 :    expected utility value
• "许用的" 英文翻译 :    admissible; allowable
• "香港通用值票" 英文翻译 :    common stored value tickets
• "不许用钩" 英文翻译 :    no hook
• "非特许用户" 英文翻译 :    unauthorized user
• "非许用炸药" 英文翻译 :    non permitted explosive
• "特许用户" 英文翻译 :    authorized user; authorizeduser; privileged user

• In this dissertation , the theories of finite element and the buckling analysis of shell are discoursed systematically . under the direction of these theories , with the help of ug software and msc / nastran software , the defective casing texture is analyzed on static strength and buckling , and then , the maximum loads of the texture with different defect value are gotten , the changeable curve of the maximum load with the defect value and the permissible defect value are gotten . that the texture with various defects can be destroyed variously is discoursed in considerable detail as well
  本论文系统论述了有限单元法和板的屈曲稳定理论，并在这些理论的指导下，以ug软件和msc nastran软件为工具，对存在一定几何缺陷的典型箱形构件进行静强度和屈曲的综合分析，分别得出了不同缺陷度的构件的极限载荷，从而得到缺陷度与极限载荷的变化曲线，给出了缺陷度的最大许用值；同时，本论文还针对不同缺陷度构件的破坏形式不同这一问题进行了详尽的论述。
• This paper trice to find the cause of effective ness loss and to analyze it theoretically by adopting the ways of quantitative analysis and quantitative analysis by using the way of fault tree to carry out the qualitative analysis , it draws the logic charts by various elements that cause the loss of effectiveness and to make a faucet tree to find out the loss programs , then make a final analysis of the smallest element of the fault tree . the first problem is due to the over friction by exceeding permitted limits ; the second problem is due to the gear feather ' s low inteusity , this paper adopts the method of changing the trans mission ratio of the first gear and the width of the sixth gear of second shaft so as to solve the problems
  本文采用定性和定量相结合的方法，利用失效树进行定性分析，它通过对可能造成系统失效的各种因素，画出逻辑框图，从上到下绘成失效树，找出失效谱，并对失效树的全部最小割集进行分析，找出有可能的失效原因，再对其通过理论计算进行定量分析，由此发现第一个问题是由于离合器在极限状况下的滑磨功超过其许用值造成的，第二个问题的原因是二轴六档齿轮强度不足。
• The one of the loss of effectiveness is the friction piece ' s bum of the clutch , there fore , in the designing of priority , the clutch ' s with of friction power is smaller than the permitted value in the reduction of the starting the truck , and it also increases the permitted condition of decreasing cloth ' s friction hot volume
  选择出摩擦片最佳参数，并保证离合器的机械性能是摩擦片参数优化的目标，本课题中由于失效形式之一是离合器摩擦片烧伤。因此，在优化设计中除保留减少汽车起步过程中离合器的单位面积滑磨功小于其许用值的约束条件外，还增加了降低离合器的滑磨热容量的约束条件。