轴位移的英文

• axial translation

• "轴"英文翻译    axle; shaft
• "位移"英文翻译    displacement; shift; drift; ...
• "视轴位移" 英文翻译 :    boresight displacement
• "座标轴位移" 英文翻译 :    displacement of coordinate axis
• "操纵杆轴位移" 英文翻译 :    auswanderung der hebelachse displaced lever axis
• "涡流式轴位移" 英文翻译 :    eddy current shaft-displacement and shaft-vibration monitor
• "轴位移变送器" 英文翻译 :    transmitter for thrust position
• "主轴位移指示器" 英文翻译 :    main shaft indicator
• "轴位" 英文翻译 :    axial view; shaft position
• "可倒转发动机的凸轮轴位移控制器" 英文翻译 :    cam shaft displacement control for reversing engines
• "长轴位" 英文翻译 :    long axis view; long-axis
• "短轴位" 英文翻译 :    short-axis
• "横轴位" 英文翻译 :    transverse view
• "轴位置" 英文翻译 :    z positionz
• "位移" 英文翻译 :    [物理学] displacement; shift; drift; shifting
• "半轴位投射" 英文翻译 :    semi-axial projection
• "赤道轴位置" 英文翻译 :    equatorial position
• "非轴位扫查" 英文翻译 :    off-axis scan
• "横轴位显示" 英文翻译 :    transaxial visualization
• "曲轴位置" 英文翻译 :    ccrank shaft position; ckcrank shaft position; ckcrankshaft position; crankshaft position
• "曲轴位置3" 英文翻译 :    ckcrankshaft position
• "散光轴位" 英文翻译 :    axis of astigmatism
• "凸轮轴位置" 英文翻译 :    cacamshaft position; cmcamshaft position
• "轴角, 轴位置" 英文翻译 :    shaft position
• "轴位断面" 英文翻译 :    axial section plane

• So , in the paper , proceeding from the automatic control of extrusion velocity and based on the basic control strategy presented firstly , the relation among parameters of the process such as pressure , temperature and displacement is investigated , and the model of the process has been built using system identification method . then , a corresponding controller is designed together with its control algorithm , and the control system is proved viable and effective by the results of simulation on the control system . in the end , the problem of the realization of the control system is discussed by using modularization method . the hardware of the control system is designed and a sofeware with a perfect manmachine interface is developed , too
  因此，本文从挤压速度的控制出发，首先探讨并确立了本系统的基本控制策略；然后根据此控制策略的必然要求，对该工艺挤压过程所涉及到的挤压力、温度、挤压轴位移等参数间的关系进行了深入研究，利用系统辨识方法建立了挤压过程关键阶段的数学模型；在此基础上完成了相应的控制器设计，给出了控制算法，并对所设计的控制系统进行了仿真。
• This paper simply introduces the device of on - line monitoring for the thrust of the rotating maching , then discu ed the finite dement analyses on the on - line monitoring elastic dement for measuring thrust in detail , in order to develop the performance of the se or and the device , we calculated the distribution of the stre 、 strain 、 axial di lacement in the elastic element using the finite element method when the axial forces f = 3 104n , the result is very satisfied
  简单介绍大型旋转机组轴向力在线监控装置，然后详细介绍轴向力测力弹性元件的有限元分析，为了提高所研制的测力传感器的性能，采用有限元方法计算了弹性元件在轴向力f = 3 104n时的应变、应力、灵敏度及轴位移等的分布情况，分析结果表明：所设计的测力传感器完全符合厂方的要求及仪表性能指标。

• 轴位移的法语：déplacement d'arbre